QuietWarmth THERMST-D Non-Programmable Thermostat User Manual

1. መግቢያ

The QuietWarmth THERMST-D Non-Programmable Thermostat is designed to provide reliable control for 120V or 240V electric radiant floor heating systems. This thermostat offers flexible temperature management, allowing you to configure it for control based on floor temperature, room temperature, or a combination of room temperature with a floor temperature limit. It features a built-in Ground Fault Circuit Interrupter (GFCI) for enhanced safety and a clear, backlit display for easy monitoring and operation. A floor sensor is included to ensure accurate temperature readings and optimal comfort.

ምስል 1: የፊት view of the THERMST-D Thermostat.

2. የደህንነት መረጃ

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or property damage.

• ማስጠንቀቂያ፡- To reduce the risk of electric shock, do not connect this device to a circuit with any phase operating down more than 150 volts to ground.
• መጫኑ በአካባቢው እና በሀገር አቀፍ የኤሌክትሪክ ኮዶች መሠረት በብቃት ባለው የኤሌክትሪክ ባለሙያ መከናወን አለበት።
• The thermostat requires connection to a dedicated 20 Amp ወረዳ
• The resistive load connected to the thermostat must not exceed 15 Amps.
• Electric radiant floor heating systems are required by the National Electrical Code to be protected by a Ground Fault Circuit Interrupter (GFCI). This thermostat has a built-in GFCI.
• Always turn off power at the circuit breaker before installing or servicing the thermostat.

ምስል 2: ጎን view of the thermostat with safety warning label.

3. የጥቅል ይዘቶች

ሁሉም እቃዎች በጥቅሉ ውስጥ መኖራቸውን ያረጋግጡ፡-

• QuietWarmth THERMST-D Non-Programmable Thermostat
• ፎቅ ዳሳሽ

4. ምርት አብቅቷልview

4.1 ቁልፍ ባህሪያት

• Non-Programmable operation for radiant floor heat systems.
• Compatible with both 120V and 240V heating systems.
• Integrated Ground Fault Circuit Interrupter (GFCI) for safety.
• Clear, backlit LED display for easy reading.
• Includes a floor sensor for precise temperature control.
• Configurable for floor temperature, room temperature, or room temperature with a floor temperature limit.
• Seven-day energy log to monitor power consumption.
• Supports multiple QuietWarmth mats: up to 120 sq ft for 120V systems, or 240 sq ft for 240V systems.

4.2 ክፍሎች

The thermostat consists of a front display unit with control buttons and a back plate for electrical connections.

• የፊት ፓነል Features a digital display showing time and temperature, along with 'Up', 'OK', and 'Down' buttons for navigation and setting adjustments.
• የኋላ ፓነል Contains wiring terminals for power input (L1, L2) and load output, as well as a connection point for the floor sensor.

ምስል 3፡ ተመለስ view የቴርሞስታት ከገመድ ተርሚናሎች ጋር።

Figure 4: Included floor sensor.

5. ማዋቀር እና መጫን

መጫኑ መከናወን ያለበት ብቃት ባለው የኤሌክትሪክ ባለሙያ ብቻ ነው።

5.1 መጫን

• The thermostat is designed for wall mounting.
• Ensure the mounting location is free from direct sunlight, drafts, or other heat sources that could affect temperature readings.

5.2 ሽቦ

Before wiring, ensure power is OFF at the circuit breaker.

1. Connect the thermostat to a dedicated 20 Amp ወረዳ
2. Identify the Line (power supply) and Load (heating mat) wires.
3. Connect the Line wires to the L1(L) and L2(N) terminals on the thermostat's back panel.
4. Connect the Load wires from the heating mat to the 'Load' terminals on the thermostat.
5. በአከባቢ ኤሌክትሪክ ኮዶች መሰረት ትክክለኛውን መሬት ማቆምን ያረጋግጡ.
6. The thermostat is dual-voltage; it can be used with either 120V or 240V heating mats, but not simultaneously. Verify your heating mat's voltagሠ ከኃይል አቅርቦት ጋር ይዛመዳል.

5.3 Floor Sensor Placement

The floor sensor is crucial for accurate floor temperature control.

• Place the sensor next to the long edge of the QuietWarmth heating mat.
• Ensure the sensor is positioned in the heated area and not near any unheated zones or external heat sources.
• Route the sensor wire carefully to avoid damage during installation of flooring materials.

ምስል 5: ዘፀample of radiant heat film installation under floating floors.

ምስል 6: ዘፀample of radiant heat film installation under tile and glued floors.

6. የአሠራር መመሪያዎች

6.1 በርቷል

After installation, restore power at the circuit breaker. The thermostat display will illuminate.

6.2 የሙቀት መጠንን ማቀናበር

• የሚለውን ተጠቀም Up እና ወደታች የሚፈለገውን የሙቀት መጠን ለማስተካከል አዝራሮች.
• የሚለውን ይጫኑ OK ምርጫዎን ለማረጋገጥ አዝራር።

6.3 የመቆጣጠሪያ ሁነታዎች

The thermostat can be configured to operate in one of three control modes:

• Floor Temperature Control: The thermostat maintains the floor at the set temperature using the floor sensor.
• የክፍል ሙቀት መቆጣጠሪያ; The thermostat maintains the room air temperature at the set point.
• Room Temperature Control with Floor Limit: The thermostat primarily controls room air temperature but prevents the floor temperature from exceeding a specified maximum limit, protecting sensitive flooring materials.

Refer to the full installation guide for instructions on how to select and configure these control modes.

6.4 Energy Log

The thermostat features a seven-day energy log, allowing you to monitor the power consumption of your radiant heating system. Consult the detailed manual for accessing and interpreting this data.

7. ጥገና

7.1 የጂኤፍሲአይ ሙከራ

For continued safety, the built-in GFCI should be tested monthly.

1. የሚለውን ይጫኑ ሙከራ button located on the bottom of the thermostat.
2. The GFCI should trip, cutting power to the heating system and indicating a fault.
3. የሚለውን ይጫኑ ዳግም አስጀምር button to restore power.
4. If the GFCI does not trip or reset correctly, discontinue use and contact a qualified electrician.

Figure 7: Bottom of the thermostat with GFCI test button.

7.2 ጽዳት

የቴርሞስታቱን ውጫዊ ክፍል ለስላሳ, መamp ጨርቅ. ገላጭ ማጽጃዎችን ወይም ፈሳሾችን አይጠቀሙ.

8. መላ መፈለግ

If you encounter issues with your QuietWarmth THERMST-D thermostat, refer to the following common problems and solutions:

• ምንም ማሳያ/ኃይል የለም፡
  • Check the circuit breaker for the dedicated circuit and ensure it is in the ON position.
  • ሁሉም የገመድ ግንኙነቶች አስተማማኝ እና ትክክለኛ መሆናቸውን ያረጋግጡ።
• Heating System Not Activating:
  • Ensure the thermostat is set to a temperature higher than the current room or floor temperature.
  • Check if the GFCI has tripped (press the RESET button if it has).
  • Confirm the correct control mode is selected (floor, room, or room with limit).
• GFCI Trips Frequently:
  • This indicates a ground fault. Immediately turn off power at the circuit breaker.
  • Inspect the heating mat and wiring for any damage or moisture.
  • Ensure the total resistive load does not exceed 15 Amps.
  • Contact a qualified electrician for diagnosis and repair.
• ትክክለኛ ያልሆነ የሙቀት ንባቦች;
  • Verify the floor sensor is correctly installed and not damaged.
  • Ensure the thermostat is not exposed to drafts, direct sunlight, or other external heat sources.

For issues not covered here, please contact QuietWarmth customer support or a qualified electrician.

9. ዝርዝሮች

10. ዋስትና እና ድጋፍ

10.1 የዋስትና መረጃ

The QuietWarmth THERMST-D Non-Programmable Thermostat comes with a 3-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

10.2 የደንበኛ ድጋፍ

For technical assistance, troubleshooting, or warranty inquiries, please contact QuietWarmth customer support. Refer to the product packaging or the manufacturer's webለአሁኑ የእውቂያ መረጃ ጣቢያ.