Aigo AC SE 120 Water Cooler Instruction Manual

1. መግቢያ

Thank you for choosing the Aigo AC SE 120 Water Cooler. This All-in-One (AIO) liquid cooling system is designed to provide efficient thermal management for your CPU, ensuring stable performance and extended component lifespan. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting.

Please read this manual thoroughly before installation and use to ensure proper setup and to prevent any damage to your system.

2. የደህንነት መረጃ

• Always disconnect power from your computer before installing or performing maintenance on any components.
• ጉዳት እንዳይደርስባቸው ክፍሎችን በጥንቃቄ ይያዙ።
• ኤሌክትሮስታቲክ ፈሳሽ (ESD) በስሱ ክፍሎች ላይ ጉዳት እንዳይደርስ ለመከላከል አንቲስታቲክ የእጅ አንጓ ማሰሪያ ይልበሱ።
• Do not open the sealed liquid cooling loop. Tampering with the unit may cause leaks and void your warranty.
• Ensure all cables are properly connected and routed to avoid interference with moving parts (e.g., fan blades).
• ልጆች በማይደርሱበት ቦታ ያስቀምጡ.

3. የጥቅል ይዘቶች

Verify that all components are present and in good condition before proceeding with installation.

• Aigo AC SE 120 Water Cooler Unit (Pump, Radiator, Fan pre-installed)
• Mounting Hardware for Intel Sockets (LGA 2066/ 2011-v3 / 2011 / 1700 / 1366 / 1200 / 115X)
• Mounting Hardware for AMD Sockets (FM1 / FM2 / FM2+ / AM2 / AM2+ / AM3 / AM3+ / AM4)
• የሙቀት ለጥፍ (ቀድሞ የተተገበረ ወይም በቱቦ ውስጥ)
• የተጠቃሚ መመሪያ

Image: Aigo AC SE 120 Water Cooler unit with its fan, radiator, pump, and various mounting brackets and screws for different CPU sockets.

4. ዝርዝሮች

5. ማዋቀር እና መጫን

This section outlines the general steps for installing your Aigo AC SE 120 Water Cooler. Specific steps may vary slightly depending on your motherboard and PC case. Always refer to your motherboard and case manuals for detailed instructions.

5.1 Prepare the CPU Socket

1. የኢንቴል ሶኬቶች፡ Attach the correct Intel backplate to the rear of your motherboard. Secure the standoffs through the motherboard holes from the front.
2. የኤኤምዲ ሶኬቶች፡ The cooler typically uses the existing AMD backplate. Remove the plastic retention clips from the stock AMD cooler mount, leaving the backplate in place. Install the appropriate AMD standoffs.
3. Ensure the CPU is correctly seated in its socket.
4. ማንኛውንም አሮጌ የሙቀት ፓስታ ወይም ቅሪት ለማስወገድ የሲፒዩውን ወለል በአይሶፕሮፒል አልኮሆል ያጽዱ።
5. Apply a thin, even layer of thermal paste to the center of the CPU's integrated heat spreader (IHS). If thermal paste is pre-applied to the water block, skip this step.

5.2 ራዲያተሩን እና ማራገቢያውን ይጫኑ

1. Determine the optimal mounting location for the 120mm radiator in your PC case. Common locations include the rear exhaust or top exhaust.
2. Mount the 120mm fan to the radiator using the provided screws. Ensure the fan is oriented to push or pull air in the desired direction (e.g., exhaust air out of the case).
3. Secure the radiator assembly to your PC case using the appropriate screws.

ምስል: ጎን view of the Aigo AC SE 120 Water Cooler, showing the radiator with a white fan attached, and the pump/water block unit.

5.3 Mount the Water Block

1. Attach the correct mounting brackets to the water block/pump unit.
2. Carefully place the water block onto the CPU, aligning the mounting holes with the standoffs.
3. Secure the water block with the provided thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

Image: The Aigo AC SE 120 Water Cooler showing the pump unit with an illuminated Aigo logo and a rainbow-colored fan on the radiator.

5.4 ገመዶችን ማገናኘት

1. Connect the pump power cable to a dedicated AIO_PUMP or CPU_FAN header on your motherboard. If your motherboard has neither, use a SYS_FAN header and ensure it is set to run at full speed in the BIOS.
2. Connect the fan power cable to the CPU_FAN header on your motherboard. If your motherboard has multiple fan headers, consult your motherboard manual for the recommended CPU fan header.
3. If your cooler has RGB lighting, connect the RGB cable to a compatible RGB header on your motherboard (e.g., 3-pin ARGB or 4-pin RGB, depending on the cooler's connector type).
4. Route all cables neatly to avoid obstructing airflow or interfering with other components.

6. የአሠራር መመሪያዎች

Once installed, the Aigo AC SE 120 Water Cooler operates automatically based on your motherboard's fan control settings.

• የመጀመሪያ ኃይል በርቷል፡ After installation, power on your computer. The pump and fan should start operating.
• ባዮስ/UEFI ቅንብሮች፡- Access your motherboard's BIOS/UEFI settings to ensure the CPU_FAN and AIO_PUMP headers are configured correctly. It is recommended to set the pump header to run at full speed (100%) for optimal cooling performance. Fan speeds can be adjusted based on temperature curves for a balance of cooling and noise.
• RGB መብራት፡ If connected to an RGB header, the lighting effects can typically be controlled via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync).
• ክትትል፡ Use system monitoring software to check CPU temperatures and ensure the cooler is functioning effectively.

ምስል፡ ከላይ ወደ ታች view of the Aigo AC SE 120 Water Cooler, highlighting the illuminated Aigo logo on the pump and the rainbow lighting of the fan.

7. ጥገና

Regular maintenance helps ensure optimal performance and longevity of your water cooler.

• አቧራ ማጽዳት; የአቧራ ክምችትን ለመከላከል የራዲያተሩን ክንፎችና የአየር ማራገቢያ ምላጮች በየጊዜው ያጽዱ፤ ይህም የአየር ፍሰትን ሊያደናቅፍ እና የማቀዝቀዣ ቅልጥፍናን ሊቀንስ ይችላል። የተጨመቀ አየር ወይም ለስላሳ ብሩሽ ይጠቀሙ።
• የደጋፊዎች ምርመራ፡- Check the fan for any signs of wear, damage, or excessive noise. Replace if necessary.
• የሆስ ምርመራ; Visually inspect the hoses for any kinks, cracks, or signs of leakage. While AIOs are sealed, regular checks are recommended.
• የሙቀት ለጥፍ; The thermal paste typically lasts for several years. If you notice a significant increase in CPU temperatures over time, consider reapplying fresh thermal paste. This requires carefully removing the water block, cleaning both surfaces, and applying new paste.

8. መላ መፈለግ

If you encounter issues with your Aigo AC SE 120 Water Cooler, refer to the following common problems and solutions:

9. ዋስትና እና ድጋፍ

The Aigo AC SE 120 Water Cooler comes with a የ 12-ወር ዋስትና ከተገዛበት ቀን ጀምሮ. ይህ ዋስትና በመደበኛ አጠቃቀም ሁኔታዎች ውስጥ የማምረቻ ጉድለቶችን እና ጉድለቶችን ይሸፍናል ።

ዋስትናው የሚከተሉትን አያካትትም-

• Damage caused by improper installation, misuse, abuse, or neglect.
• ባልተፈቀደ ማሻሻያ ወይም ጥገና ምክንያት የሚደርስ ጉዳት።
• በተፈጥሮ አደጋዎች ወይም አደጋዎች ምክንያት የሚደርስ ጉዳት.

For technical support, warranty claims, or further assistance, please contact your retailer or the Aigo customer service department. Please have your proof of purchase and product model number (ACSE120-BK) ready when contacting support.