1. መግቢያ
This manual provides detailed instructions for the installation, configuration, and operation of your SpeedyBee F405 V5 Flight Controller (FC) and BLS 55A 4-in-1 Electronic Speed Controller (ESC) stack. This high-performance stack is designed for FPV drones, offering advanced features and robust performance. Please read this manual thoroughly before use to ensure proper setup and safe operation.
2. የደህንነት መረጃ
⚠️ ለመዝናኛ አገልግሎት ብቻ። ድሮኖችን/አውሮፕላኖችን በህገ ወጥ መንገድ መቀየር የተከለከለ ነው። እባኮትን ህጋዊ አጠቃቀምን ለማረጋገጥ በአገርዎ/በአካባቢዎ ድሮኖችን/አውሮፕላኖችን ስለመጠቀም ለሚመለከተው ህጎች እና መመሪያዎች ትኩረት ይስጡ።
- Always ensure correct polarity when connecting power. Incorrect wiring can cause severe damage to the components.
- በሚሸጡበት ጊዜ ጥንቃቄ ያድርጉ. ተገቢውን የደህንነት መሳሪያ ይጠቀሙ እና የአየር ማናፈሻን ያረጋግጡ።
- Keep the stack away from moisture and extreme temperatures.
- Disconnect the battery before performing any maintenance or modifications.
- Ensure all connections are secure before powering on your drone.
3. የጥቅል ይዘቶች
The SpeedyBee F405 V5 Stack BLS 55A is available in different configurations. Please verify your package contents against the list below.
መደበኛ ጥቅል ይዘቶች
- SpeedyBee F405 V5 ሞዴል የአውሮፕላን በረራ መቆጣጠሪያ x1
- SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
- Model Aircraft Stack Connector Cable (SH1.0 10pin*25mm) x1
- Model Aircraft Stack Connector Cable (SH1.0 10pin*75mm) x1
- DJI Air Unit Connector Cable (SH1.0 6pin*80mm) x1
- የጂፒኤስ ባለ 6-ፒን ማያያዣ ገመድ + ባለ 6-ፒን SH1.0 ተርሚናል x1 (SH1.0 ባለ 6-ፒን*120ሚሜ)
- የጂፒኤስ 4ፒን ማያያዣ ገመድ + 4ፒን SH1.0 ተርሚናል x1 (SH1.0 ከSH1.0 6ፒን እስከ SH1.0 4ፒን*120ሚሜ)
- ተቀባይ 4ፒን ማያያዣ ገመድ x1 (SH1.0 4ፒን*100ሚሜ)
- XT60 የኃይል ገመድ x1 (120ሚሜ)
- የኤም3 ሞዴል የአውሮፕላን ቁልል መጫኛ ዊንጮች x4 (30ሚሜ)
- M3 ሄክስ ናይሎን ለውዝ x5
- M3 ጥቁር የሲሊኮን ማጠቢያዎች x5
- የካፓሲተር ሙቀት መጨመሪያ ቱቦ x2
- የሞዴል ኤርክራፍት ኤፍሲ ሲሊኮን ሽፋኖች x5
- የሞዴል አውሮፕላን ESC የሲሊኮን ሽፋኖች x5
- 35V 1000uF ጠጣር ካፓሲተር x1
- ለሞዴል አውሮፕላን ቁልል ፈጣን ጅምር መመሪያ x1
Deluxe Package Contents
- SpeedyBee F405 V5 ሞዴል የአውሮፕላን በረራ መቆጣጠሪያ x1
- SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
- የመሸጫ ልምምድ ቦርድ x1
- የአጭር-ወረዳ መከላከያ መሳሪያ x1
- Model Aircraft Stack Connector Cable (SH1.0 10pin*25mm) x1
- Model Aircraft Stack Connector Cable (SH1.0 10pin*75mm) x1
- DJI Air Unit Connector Cable (SH1.0 6pin*80mm) x1
- የጂፒኤስ ባለ 6-ፒን ማያያዣ ገመድ + ባለ 6-ፒን SH1.0 ተርሚናል x1 (SH1.0 ባለ 6-ፒን*120ሚሜ)
- የጂፒኤስ 4ፒን ማያያዣ ገመድ + 4ፒን SH1.0 ተርሚናል x1 (SH1.0 ከSH1.0 6ፒን እስከ SH1.0 4ፒን*120ሚሜ)
- ተቀባይ 4ፒን ማያያዣ ገመድ x1 (SH1.0 4ፒን*100ሚሜ)
- ባዘር ቀይ እና ጥቁር ሽቦዎች x1 (100ሚሜ)
- አክቲቭ ባዘር x1
- የአይነት-ሲ ኤክስቴንሽን ሞዱል 4ፒን ኮኔክተር ኬብል x1 (SH1.0 4ፒን*80ሚሜ)
- የአይነት-ሲ ኤክስቴንሽን ሞዱል x1
- M3 ሄክስ ናይሎን ለውዝ x5
- M3 ጥቁር የሲሊኮን ማጠቢያዎች x5
- የሞዴል ኤርክራፍት ኤፍሲ ሲሊኮን ሽፋኖች x5
- የሞዴል አውሮፕላን ESC የሲሊኮን ሽፋኖች x5
- የM3 ቁልል መጫኛ ዊንጮች x4 (30ሚሜ)
- የኃይል ማስፋፊያ ቦርድ x4
- የካፓሲተር ሙቀት መጨመሪያ ቱቦ x2
- 35V 1000uF ጠጣር ካፓሲተር x1
- ለሞዴል አውሮፕላን ቁልል ፈጣን ጅምር መመሪያ x1
4. ምርት አብቅቷልview
ስፒዲቢ F405 V5 የበረራ መቆጣጠሪያ
The F405 V5 Flight Controller features an STM32F405 MCU and an ICM42688P Gyro for precise flight control. It includes a built-in barometer (SPA06-003) for accurate altitude readings and an AT7456E OSD chip for on-screen display. Connectivity includes a new Type-C USB port and full-featured Bluetooth tuning via the SpeedyBee App, allowing for wireless firmware flashing and parameter tuning. It supports 6-pin direct plug-in or solder connection for DJI Air Units and has a built-in 16MB Blackbox storage chip for flight data logging.
Power outputs include 9 groups of 5V output (total 1.5A), 2 groups of 9V output (total 3A) with PINIO remote on/off control, 1 group of 3.3V output, and 3 groups of 4.5V output (max 1A) for peripherals like receivers and GPS modules. It supports 8 motor outputs (M1-M4 on bottom, M5-M8 on front) and multiple UARTs for various peripherals.
ስፒዲቢ BLS 55A 4-in-1 ESC
The BLS 55A 4-in-1 ESC is designed for 3-6S LiPo input, providing a continuous current of 55A per channel (220A total) and a burst current of 70A (280A total) for 10 seconds. It features a built-in TVS protective diode for surge protection and includes a 1000uF Low ESR Capacitor in the package for enhanced stability. The ESC supports DSHOT300/600 protocols and current sensing (Scale=400, Offset=0). It also supports ESC Telemetry.
5. መጫን
በመጫን ላይ
The SpeedyBee F405 V5 FC and BLS 55A ESC both feature 30.5 x 30.5mm mounting holes with a 4mm hole diameter. They are designed to be stacked together using the provided silicone grommets and screws.
Connecting the FC and ESC
The FC and ESC can be connected via a 10-pin connector or by direct soldering. The 10-pin design provides enhanced safety redundancy.
6. የሽቦ ንድፎች
Comprehensive Wiring Diagram
የዲጄአይ አየር ክፍል ግንኙነት
Receiver Specific Notices
7. ውቅር
Wireless Tuning via SpeedyBee App
The SpeedyBee F405 V5 FC supports full-featured Bluetooth tuning. Connect to the SpeedyBee App on your smartphone to flash FC firmware, tune parameters, and configure your quad anytime, anywhere. Ensure MSP is enabled with Baud rate 115200 on UART4 for Bluetooth connection.
የሞተር አቅጣጫ ለውጥ
You can change motor directions wirelessly using the SpeedyBee app. Connect to the app, navigate to 'Motors' and then 'Motor Direction Settings' to adjust as needed.
የ LED ስትሪፕ መቆጣጠሪያ
The FC supports 4 sets of LED pads. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to LED1-LED4 connectors on the bottom side. Short-press the BOOT button to cycle through different LED displaying modes. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.
8. የአሠራር መመሪያዎች
Once installed and configured, your SpeedyBee F405 V5 Stack is ready for flight. Ensure your radio transmitter is properly bound and configured with your receiver. Always perform pre-flight checks, including propeller security, battery level, and control surface response, before each flight.
- አብራ፡ Connect your LiPo battery to the XT60 connector. The FC and ESC will initialize.
- መታጠቅ፡ Arm your drone using your configured arming switch on your radio transmitter.
- በረራ፡- Operate your drone according to standard FPV flight practices.
- ትጥቅ መፍታት፡ Disarm your drone using your configured disarming switch after landing.
9. መላ መፈለግ
Flight Controller Not Responding / Bricked
If your FC becomes unresponsive or appears 'bricked', you can force it into DFU (Device Firmware Upgrade) mode for firmware flashing:
- Press and hold the BOOT button on the FC.
- While holding the BOOT button, connect the FC to your computer via the USB Type-C cable.
- The FC should now be in DFU mode, allowing you to flash new firmware using Betaflight Configurator.
SD Card Compatibility Issues
Betaflight firmware requires the microSD card to be either Standard (SDSC) or High Capacity (SDHC) and under 32GB. Extended Capacity cards (SDXC) are not supported. The microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format. While you can use any SD card less than 32GB, Betaflight can only recognize a maximum of 4GB. It is recommended to use a 3rd party formatting tool and choose 'Overwrite format' when formatting your card.
10. ዝርዝሮች
SpeedyBee F405 V5 30.5×30.5mm Model Aircraft Flight Controller
| ባህሪ | ዝርዝር መግለጫ |
|---|---|
| ኤም.ሲ.ዩ | STM32F405 |
| IMU (ጋይሮ) | ICM42688P |
| የዩኤስቢ ወደብ ዓይነት | አዲስ የType-C በይነገጽ |
| ባሮሜትር | SPA06-003 |
| OSD ቺፕ | AT7456E |
| ሙሉ-ተለይቶ የቀረበ የብሉቱዝ ማስተካከያ | የተደገፈ። ለFC firmware ብልጭታ እና የፓራሜትር ማስተካከያ በSpeedyBee መተግበሪያ በኩል ይገናኙ። |
| ገመድ አልባ FC የጽኑ ትዕዛዝ ማሻሻል | የሚደገፍ |
| የዲጄአይ አየር ክፍል ግንኙነት | ባለ 6-ፒን ቀጥተኛ ተሰኪ ወይም የሶለር ግንኙነትን ይደግፋል |
| ብላክቦክስ | የተደገፈ፣ አብሮ የተሰራ 16ሜባ የማከማቻ ቺፕ |
| ግብዓት Voltage | 3-6S LiPo ባትሪ |
| ገለልተኛ 5V BEC ውፅዓት | 9 ቡድኖች (በፊት ለፊት 4× + 5V ፓዶች፣ 1× BZ+ ባዘር ፓድ፣ እና ለውጭ LEDዎች ማዕዘኖች ላይ 4× + 5V ፓዶች)። ጠቅላላ የውጤት ፍሰት፡ 1.5A። |
| ገለልተኛ 9V BEC ውፅዓት | 2 ቡድኖች (በፊት በኩል 1x 9V ፓድ፣ በጀርባው ላይ ባለው ማገናኛ ውስጥ 1x 9V ውፅዓት)። ጠቅላላ የውጤት ፍሰት፡ 3A። የፒንዮ የርቀት መቆጣጠሪያን ማብሪያ/ማጥፋት ይደግፋል። |
| ኤምሲዩ እና ጋይሮ ፓወር | ገለልተኛ ኤልዲኦ |
| 3.3V ውፅዓት | 1 ቡድን (1 × 3.3V ፓድ በፊት በኩል) |
| 4.5V ውፅዓት | 3 ቡድኖች (በፊት ለፊት 3× 4.5V ፓዶች)። FC በዩኤስቢ ሲሰራ የኃይል ተቀባይ እና ጂፒኤስ። ከፍተኛው የውጤት ፍሰት፡ 1A። |
| የ ESC ምልክት | የM1-M4 ፓዶች እና 10-ፒን ማያያዣ በጀርባው ላይ |
| ሰርቮ ሲግናል | የS5-S6 ፓዶች ከፊት ለፊት |
| የESC ቴሌሜትሪ ግብዓት | የተደገፈ (UART5) |
| የቤታፍላይት ካሜራ ማስተካከያ ፓድ | የተደገፈ (የሲሲ ፓድ ከፊት በኩል) |
| I2C | የሚደገፍ (የጂፒኤስ ማገናኛ + ፓዶች) |
| UART | UART1 (ብሉቱዝ)፤ UART2 (ለተቀባዩ የፊት ፓዶች)፤ UART3 (DJI VTX ፓዶች + የኋላ SH1.0-6-ፒን)፤ UART4 (የጂፒኤስ ፓዶች + የፊት SH1.0-6-ፒን)፤ UART5 (TLM)፤ UART6 (የመቀበያ ፓዶች + የኋላ SH1.0-4-ፒን) |
| የኤስቲ ኤልኢዲ ፓዶች | የሚደገፍ፣ በፊት G/5V/LED ፓዶች ላይ፤ በFC firmware ቁጥጥር ስር ያለ፤ |
| የሜትዮር ኤልኢዲ ስትሪፕ ፓዶች | የሚደገፍ። በ BOOT አዝራር ወይም መተግበሪያ በኩል በ SB-LED እና ST-LED ሁነታዎች መካከል ይቀያይሩ። በ SB-LED ሁነታ፣ በ ESP32 ብሉቱዝ ቺፕ ቁጥጥር ስር። |
| Buzzer Pads | የሚደገፍ |
| BOOT ቁልፍ | [ሀ] የDFU ሁነታ እንዲበራ ለማስገደድ ቡትን ማብራት ላይ እያሉ ይያዙ። [ለ] ሲበራ እና በተጠባባቂነት ላይ ሲሆን፣ አጭር-ፕሬስ ዑደት የኤልኢዲ ማሳያ ሁነታዎች፤ ረጅም-ፕሬስ ማብሪያ / ማጥፊያዎች SB-LED/ST-LED። በST-LED ሁነታ፣ ኤልኢዲ1–LED4 በFC firmware ቁጥጥር ይደረግባቸዋል። |
| RSSI ፓዶች | የሚደገፍ |
| SmartPort | አይደገፍም። |
| የሚደገፍ FC Firmware | ቤታፍላይት፣ አይኤንቪ፣ አርዱፓይለት |
| የጽኑ ትዕዛዝ ዒላማ ስም | SPEEDYBEEF405V5 |
| የፋብሪካ የጽኑ ትዕዛዝ ስሪት | ቤታፍላይት 4.5.2 |
| የማዋቀሪያ ስሪት | ቤታፍላይት 10.10.0 |
| የመጫኛ ጉድጓዶች | 30.5 × 30.5 ሚሜ (Ø4 ሚሜ)፣ የጎን መክፈቻ |
| መጠኖች | 39ሚሜ (ኤል) × 39 ሚሜ (ወ) × 4.9 ሚሜ (ኤች) |
| ክብደት | 8.1 ግ |
ስፒዲቢ ኦክስ32 55A 30.5×30.5 4-በ-1 ESC
| ባህሪ | ዝርዝር መግለጫ |
|---|---|
| ነባሪ firmware | OX32 |
| ቀጣይነት ያለው ወቅታዊ | 55A (በአንድ ቻናል) / 220A (በ1 4) |
| ከፍተኛው የአሁኑ | 70A (በአንድ ቻናል) / 280A (በ1 4) |
| የቲቪኤስ መከላከያ ዳዮድ | አዎ (አብሮ የተሰራ) |
| ውጫዊ Capacitor | 1000µF ጠጣር ካፓሲተር (በጥቅሉ ውስጥ ተካትቷል) |
| የESC/ሞተር ፕሮቶኮል | DSOT300/600 |
| ግብዓት Voltage | 3-6S LiPo |
| የኃይል ውፅዓት | ቪቢቲ |
| የአሁኑ ዳሳሽ | የሚደገፍ |
| ESC ቴሌሜትሪ | የሚደገፍ |
| የመጫኛ ጉድጓዶች | 30.5 × 30.5 ሚሜ (Ø4 ሚሜ)፣ የጎን መክፈቻ |
| መጠኖች | 40.9ሚሜ (ሊ) × 44.9ሚሜ (ወ) × 8.0ሚሜ (ሰ) (ሙቀትን ጨምሮ) |
| ክብደት | 19.1 ግ |
| የአሁኑ የመለኪያ ማስታወሻ | የተደገፈ (ልኬት=27፣ ከቦታው ጋር የሚመጣጠን =-2644) |
11. የተጠቃሚ ምክሮች
- የገመድ አልባ ምቾት; ሙሉ አድቫን ይውሰዱtage of the SpeedyBee app's wireless tuning capabilities. This eliminates the need for a laptop in the field for minor adjustments or quick checks.
- Capacitor is Key: Always install the included low ESR capacitor. It's crucial for protecting your flight controller from voltage spikes, especially during aggressive maneuvers or power-intensive operations.
- የኤስዲ ካርድ ቅርጸት፡ If you experience issues with Blackbox logging, double-check your microSD card's format (FAT16/FAT32) and ensure it's an SDSC or SDHC type under 32GB. Reformatting with an 'Overwrite format' option can often resolve problems.
- ተቀባዩ ሽቦ Pay close attention to the specific wiring instructions for SBUS and ELRS receivers, especially when integrating with DJI Air Units, to avoid recognition issues.
12. ዋስትና እና ድጋፍ
For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty-related inquiries. Always refer to the official SpeedyBee website for the latest firmware updates and support resources.
