Pro-Ject RM 1.3 Turntable User Manual

መግቢያ

This manual provides essential instructions for the setup, operation, and maintenance of your Pro-Ject RM 1.3 Turntable. Please read it thoroughly before use to ensure proper functionality and longevity of your device.

የጥቅል ይዘቶች

Before proceeding with the setup, please verify that all components are present:

• Pro-Ject RM 1.3 Turntable Unit
• ፕላስተር
• ድራይቭ ቀበቶ
• Outboard 15V AC Motor
• የኃይል አቅርቦት
• Sumiko Pearl Cartridge (pre-installed or separate)
• Removable RCA Cables
• የክብደት ክብደት
• ፀረ-ስኬቲንግ ክብደት
• የስታይለስ ግፊት መለኪያ

የማዋቀር መመሪያዎች

Follow these steps carefully to set up your turntable:

1. ማሸግ፡ Carefully remove all components from the packaging. Retain packaging for future transport.
2. የፕላስተር ጭነት; Place the platter onto the central spindle. Ensure it sits securely and rotates freely.
3. የሞተር አቀማመጥ; Position the outboard motor unit next to the turntable chassis. The motor pulley should align with the outer rim of the platter.
4. Drive Belt Installation: Gently stretch the drive belt around the motor pulley and the outer rim of the platter. Ensure the belt is not twisted.
5. Cartridge Installation (if not pre-installed): If your Sumiko Pearl cartridge is not pre-installed, carefully attach it to the tonearm headshell using the provided screws. Ensure correct alignment.
6. የክብደት ማስተካከያ፡ Slide the counterweight onto the rear of the tonearm. Adjust it until the tonearm floats horizontally. Then, set the tracking force according to the cartridge manufacturer's recommendations (typically 1.8g for Sumiko Pearl). Use a stylus pressure gauge for accuracy.
7. የበረዶ መንሸራተትን የሚከላከል ማስተካከያ፦ Attach the anti-skating weight to the tonearm's anti-skating mechanism. Adjust the setting to match the tracking force.
8. በመገናኘት ላይ Ampማስታገሻ ፦ Connect the removable RCA cables from the turntable's output to the "Phono" input of your amplifier or a dedicated phono preamplifier. Ensure the ground wire is connected between the turntable and your ampአነቃቂ/ቅድመamplifier to minimize hum.

የአሠራር መመሪያዎች

1. አብራ፡ Connect the power supply to the motor unit and a wall outlet. Press the power button on the motor unit to start the platter rotation.
2. ፍጥነት ይምረጡ፡ Most turntables offer 33 1/3 RPM and 45 RPM. Ensure the correct speed is selected for your record. (Refer to motor unit for speed selection mechanism, typically a switch or belt position change).
3. የቦታ መዝገብ፡- Carefully place your vinyl record onto the platter.
4. የታችኛው ቶን አርም፦ Gently lift the tonearm using the cueing lever. Position the stylus over the desired track on the record. Slowly lower the cueing lever to allow the stylus to descend onto the record groove.
5. መልሶ ማጫወት፡ The record will now play. Adjust the volume on your ampማብሰያ
6. መልሶ ማጫወትን ማቆም፡ At the end of the record, or when you wish to stop, use the cueing lever to lift the tonearm from the record. Return the tonearm to its rest and secure it. Press the power button on the motor unit to stop the platter.

ጥገና

• የመዝገብ ማጽዳት; Regularly clean your vinyl records using a dedicated record brush or cleaning solution to remove dust and static.
• የስታይለስ እንክብካቤ; Use a soft stylus brush to gently clean the stylus tip before and after each play. Brush from back to front. Avoid touching the stylus with your fingers.
• የማጠፊያ ማጽጃ; Wipe the turntable chassis and platter with a soft, dry, lint-free cloth. Avoid abrasive cleaners or solvents.
• ቀበቶ ምርመራ; Periodically check the drive belt for wear or stretching. Replace if necessary to maintain accurate playback speed.

መላ መፈለግ

በተርንቴብልዎ ላይ ችግሮች ካጋጠሙዎት የሚከተሉትን የተለመዱ ችግሮች እና መፍትሄዎች ይመልከቱ፡

ዝርዝሮች

ዋስትና እና ድጋፍ

For warranty information, please refer to the documentation provided with your purchase or visit the official Pro-Ject website. For technical support or service inquiries, please contact your authorized Pro-Ject dealer or the manufacturer's customer service department.

ለዋስትና ጥያቄዎች የግዢ ማረጋገጫዎን ያስቀምጡ።