1. ምርት አብቅቷልview
The Ozito Air Spray Gun (Model: 4472350) is a versatile tool designed for efficient application of various coatings. Its suction-feed design and adjustable controls make it suitable for a wide range of painting tasks, from general-purpose spraying to applying specific finishes and sealants. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.

Figure 1: Ozito Air Spray Gun with attached 1000 ml paint pot.
2. የደህንነት መረጃ
ይህንን ምርት ሲጠቀሙ የእሳት፣ የኤሌክትሪክ ንዝረት እና የግል ጉዳት አደጋን ለመቀነስ ሁልጊዜ መሰረታዊ የደህንነት ጥንቃቄዎችን ይከተሉ።
- መመሪያውን ያንብቡ፡- Thoroughly read and understand all instructions before operating the spray gun.
- የግል መከላከያ መሣሪያዎች (PPE)፡- Always wear appropriate eye protection (safety glasses/goggles), respiratory protection (respirator mask), and protective gloves.
- የአየር ማናፈሻ; Use the spray gun in a well-ventilated area to avoid inhalation of fumes and to prevent the buildup of flammable vapors.
- ተቀጣጣይ ቁሶች; Do not spray flammable or combustible materials near open flames, pilot lights, or other ignition sources.
- የኤሌክትሪክ ደህንነት; Ensure your air compressor and any extension cords are properly grounded and rated for the power requirements.
- ልጆችን ያርቁ; Do not allow children or untrained persons to operate the spray gun.
- አስተማማኝ ግንኙነቶች; Ensure all air hose connections are secure before operation.
3. ክፍሎች እና ክፍሎች
The Ozito Air Spray Gun comes with the following main components:
- Suction Spray Gun Body
- 1.5 mm Nozzle (pre-installed or included)
- 1000 ml Paint Pot (Suction Cup)
- Fluid Adjustment Dial
- Fan Adjustment Dials
- የአየር ማስገቢያ ማገናኛ

ምስል 2: ጎን view of the Ozito Air Spray Gun, showing the handle and air inlet.
4. ማዋቀር
- ማሸግ ፦ ሁሉንም ንጥረ ነገሮች ከማሸጊያው ውስጥ በጥንቃቄ ያስወግዱ. ለማንኛውም ጉዳት ይፈትሹ.
- Connect Air Compressor: Attach a suitable air hose (not included) from your air compressor to the air inlet connector on the spray gun. Ensure the compressor can provide a minimum flow rate of 85 liters per minute.
- ቁሳቁስ ማዘጋጀት; Prepare your paint, topcoat, or sealant according to the manufacturer's instructions. Ensure it is properly thinned for spraying consistency.
- Fill Paint Pot: Unscrew the paint pot from the spray gun body. Fill the pot with your prepared material, ensuring not to overfill. Reattach the paint pot securely to the spray gun.
- የመጀመሪያ ማስተካከያዎች፡ Before spraying, make initial adjustments to the fluid and fan pattern dials. Start with a moderate setting.
5. የአሠራር መመሪያዎች
- የኃይል ማብሪያ / ማጥፊያ: Turn on your air compressor and allow it to build up sufficient pressure.
- የሙከራ ስፕሬይ ንድፍ Before spraying your actual workpiece, test the spray pattern on a piece of scrap material. Adjust the fluid adjustment dial to control the amount of material sprayed and the fan adjustment dials to change the spray pattern (e.g., from a round to a flat pattern).
- የመርጨት ዘዴ; Hold the spray gun perpendicular to the surface, maintaining a consistent distance (typically 6-10 inches). Use smooth, even strokes, overlapping each pass by about 50%. Release the trigger at the end of each stroke.
- መሙላት፡ If the paint pot runs low, turn off the air supply, unscrew the pot, refill, and reattach before resuming.
6. ጥገና
Proper cleaning and maintenance are crucial for the longevity and performance of your spray gun.
- ወዲያውኑ ማጽዳት; Clean the spray gun immediately after each use. Do not allow material to dry inside the gun.
- ማስወገጃ- Disassemble the paint pot, nozzle, and air cap.
- የጽዳት ክፍሎች፡- Clean all components thoroughly with an appropriate cleaning solution (e.g., paint thinner for oil-based paints, water for water-based paints). Use a cleaning brush to remove any residue from the nozzle and internal passages.
- እንደገና መሰብሰብ፡ Reassemble the spray gun once all parts are clean and dry.
- ማከማቻ፡ Store the spray gun in a clean, dry place, away from extreme temperatures and direct sunlight.
7. መላ መፈለግ
| ችግር | ሊሆን የሚችል ምክንያት | መፍትሄ |
|---|---|---|
| ምንም የሚረጭ ወይም ደካማ የሚረጭ | Clogged nozzle or air cap; insufficient air pressure; material too thick. | Clean nozzle and air cap; check compressor pressure; thin material. |
| ያልተስተካከለ የመርጨት ንድፍ | Dirty air cap; damaged nozzle; incorrect fan adjustment. | Clean air cap; replace nozzle if damaged; adjust fan dials. |
| Material spitting | Material too thick; air leak; low material in pot. | Thin material; check connections for leaks; refill paint pot. |
8. ዝርዝሮች
- የሞዴል ስም፡- ASG-SFEU; EX; UK
- የሞዴል ቁጥር፡- 4472350
- የምርት ስም፡ ኦዚቶ
- የኖዝል መጠን፡ 1.5 ሚ.ሜ
- Paint Pot Capacity: 1000 ሚሊ ሊትር
- Minimum Air Compressor Flow Rate: 85 ሊትር በደቂቃ
- ቀለም፡ ግራጫ
- የተካተቱ አካላት፡- 1 suction spray gun
- የጥቅል መጠኖች: 28.5 x 19 x 11 ሴ.ሜ
- የእቃው ክብደት፡ 790 ግራም
- አምራች፡ አይንሄል
9. ዋስትና እና ድጋፍ
For information regarding warranty coverage, spare parts availability, or technical support, please refer to the official Ozito website or contact Ozito customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
የመስመር ላይ መርጃዎች፡- ጎብኝ www.ozito.com.au (or your regional Ozito website) for product registration, FAQs, and support contact details.





