Waterdrop WD-KJF Filter Replacement Manual

መግቢያ

This manual provides essential information for the proper replacement of your Waterdrop WD-KJF filter, designed for the Waterdrop WD-KJ600 Reverse Osmosis Instant Hot Water Dispenser System. Adhering to these instructions ensures optimal performance and longevity of your water filtration system.

ቁልፍ ባህሪያት

• Adaptive Design: Specifically designed for compatibility with Waterdrop WD-KJ600 and WD-K6-W systems.
• Upgraded Filtration: Utilizes RO membrane technology with 0.0001 µm accuracy to effectively reduce TDS, heavy metals, fluoride, and organic matter.
• 5-in-1 Advanced Purification: Features a post-position activated carbon block and RO membrane to reduce most contaminants and absorb residual chlorine odors and organics.
• ረጅም የአገልግሎት ሕይወት; Provides clean, pure filtered water for up to 12 months or 1,600 gallons, ensuring consistent water quality.
• ቀላል ጭነት; Designed for quick, tool-free filter changes in approximately 3 seconds with a simple twist mechanism.

ምርት አልቋልview

የደህንነት መረጃ

Always ensure the system is unplugged before performing any maintenance beyond filter replacement. Do not attempt to disassemble the filter or the main unit. Use only genuine Waterdrop replacement filters to maintain product warranty and performance. Keep the product away from direct sunlight and heat sources.

የማጣሪያ ምትክ

The Waterdrop WD-KJF filter is designed for easy, direct replacement without needing to shut off the main water supply or power. Follow these steps:

1. ለመተካት ዝግጅት ያድርጉ; Turn off the tap and wait for 30 seconds to fully release any residual pressure from the system.
2. የድሮ ማጣሪያን ያስወግዱ; Locate the filter compartment. Twist the old filter counter-clockwise until it detaches, then pull it out.
3. አዲስ ማጣሪያ ጫን፡- Insert the new WD-KJF filter into the compartment. Twist it clockwise until the filter handle aligns with the display bar, indicating it is securely in place.
4. የማጣሪያ ህይወት አመልካችን ዳግም አስጀምር፦ On the system's control panel, press and hold the filter reset key (labeled 'KJF') for 5 seconds. You will hear a 'beep' sound, and the indicator light will turn blue, confirming the reset.
5. ስርዓቱን ያጥፉ; After resetting, the system will automatically flush for 60 seconds. Following this, the cold water key will flash. Touch this key to initiate a manual flush for 15 minutes, or until the faucet stops dispensing water. This ensures any air or carbon fines are cleared from the new filter.

ኦፕሬሽን

Once the filter is replaced and flushed, your Waterdrop WD-KJ600 system is ready for use. The smart touch faucet allows for precise temperature control and instant dispensing of purified water.

ጥገና

Regular filter replacement is crucial for maintaining the quality of your purified water and the efficiency of your Waterdrop system. The WD-KJF filter has a recommended service life of 12 months or 1,600 gallons. Always monitor the filter life indicator on your system and faucet, and replace the filter promptly when indicated.

መላ መፈለግ

If you experience issues such as reduced water flow, unusual taste, or persistent filter indicator warnings after replacement, please refer to the main Waterdrop WD-KJ600 system manual or contact Waterdrop customer support for assistance. Ensure the filter is correctly installed and fully flushed after replacement.

ዝርዝሮች

ዋስትና እና ድጋፍ

For warranty information, technical support, or to purchase additional replacement filters, please visit the official Waterdrop webጣቢያ ወይም የደንበኛ አገልግሎታቸውን ያነጋግሩ። ለዋስትና ጥያቄዎች የግዢ ደረሰኝዎን ያስቀምጡ።