Cdtech TP300 Bluetooth Module Owner’s Manual

Cdtech TP300 Bluetooth Module

አልቋልview
CDI-WC46600A-01 is a Wi-Fi + BLE module independently developed by Cdtech based on the ECR6600-ATS2L chip. ECR6600-ATS2L is a SoC chip designed for smart home IoT terminal devices, supporting Wi-Fi 802.11b/g/n/ax and BLE 5.1 protocols. It includes a power management module, power ampማነቃቂያ, ዝቅተኛ-ጫጫታ amplifier, and transceiver switch. ECR6600-ATS2L adopts a RISC processor architecture, has ample storage space, rich peripheral interfaces, a more secure encryption mechanism, an on-chip FullMAC architecture, and a wider operating temperature range.

ባህሪያት

የWi-Fi ባህሪዎች

• Supports IEEE 802.11 b/g/n/ax
• LMAC እና UMACን ጨምሮ ሙሉ MACን ይደግፋል
• Supports SoftAP, STA, and Wi-Fi direct connection mode
• Supports WMM QoS
• Supports 0.8/1.6/3.2 US security protection intervals
• Supports 802.11 ax MCS0 – MCS7
• The maximum bit rate reaches 150 Mbps
• Both uplink and downlink support MU-OFDMA (STA is supported)
• STA supports beamforming (STA acts as the Beamformer)
• መካከለኛ-ambleን ይደግፋል
• Supports 20 M and 40 M bandwidth. 802.11ax only supports 20 M bandwidth.
• Supports dual carrier modulation (Dual Carrier Modulation, DCM)

የ BLE ባህሪ

• Supports BLE 5.1 protocol (does not support AOA/AOD)
• Supports single-device BLE connection
• Supports synchronous broadcasting and scanning
• Supports enhanced power control
• Output power up to +8 dBm
• Supports adaptive frequency hopping (AFH)
• ያልተመሳሰለ ውሂብ መላክ እና መቀበልን ይደግፋል
• የግንኙነት መለኪያ ማሻሻያ ይደግፋል
• Supports extensible data packet length
• የአገናኝ ንብርብር ምስጠራን ይደግፋል
• LE ፒንግን ይደግፋል

The Wi-Fi subsystem and BLE subsystem share the radio part, including ADC/DAC/PLL. Wi-Fi and BLE can only have one working at a time.

አጠቃላይ መግለጫ

Pin description and PCBA size

Note: Method for downloading the module: VCC, GND, EN (pull-up), UART0_TX, UART0_RX, RESET_B (connected to the RTS of the serial port)

Module physical picture

የቁሳቁሶች ቢል

የኤሌክትሪክ ባህሪያት

Direct-current characteristic

Suggested working conditions

Reflow soldering curve graph

ወደ IPC/JEDEC መስፈርት ተጠቅሷል።

• ከፍተኛ ሙቀት፡ <250°C
• የጊዜ ብዛት፡ ≤2 ጊዜ

package figure

የማሸጊያ መመሪያዎች

1. 700 pcs

   • Each reel is loaded with 700 pcs (leave 20 empty pockets at both the front and back without components).

2. Perform vacuum packaging once the taping process is complete.

3. After vacuum packaging, place the taped reel into the inner box (700 pcs total per box).

4. 700pcs × 5 = 3500pcs

   • Each outer carton holds 5 inner boxes, for a total capacity of: $700\text{ pcs} \times 5 = 3500\text{ pcs}$.

WC46600A-01 is an ESD (Electrostatic Discharge) sensitive component. ESD or peak voltage may cause damage to the device. Although the WC46600A-01 has an internal ESD protection circuit, please handle it with care to avoid causing permanent damage or performance degradation.

ማረጋገጫ
በ KDB 996369 D03 OEM ማንዋል v01r01 መሠረት ለአስተናጋጅ ምርት አምራቾች የውህደት መመሪያዎች

የሚመለከታቸው የ FCC ደንቦች ዝርዝር
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter.

የተወሰኑ የአሠራር ሁኔታዎች አጠቃቀም
Antenna Placement Within the Host Platform The module is tested for mobile RF exposure use condition.. The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for exampየተወሰኑ የላፕቶፕ አወቃቀሮች ወይም ከሌላ አስተላላፊ ጋር አብሮ መገኛ)፣ ከዚያ የFCC ፈቃድ ልክ እንደሆነ አይቆጠርም እና የFCC መታወቂያ በመጨረሻው ምርት ላይ መጠቀም አይቻልም። በነዚህ ሁኔታዎች የኦሪጂናል ዕቃ አምራች ኢንተግራተር የመጨረሻውን ምርት (ማስተላለፊያውን ጨምሮ) እንደገና ለመገምገም እና የተለየ የFCC ፍቃድ የማግኘት ሃላፊነት አለበት።

የተወሰነ ሞጁል ሂደቶች
አይተገበርም።

የዱካ አንቴና ንድፎች
አይተገበርም።

የ RF ተጋላጭነት ግምት
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

አንቴና አይነት እና ትርፍ

• የሚከተሉት አንቴናዎች በዚህ ሞጁል ለመጠቀም ማረጋገጫ ተሰጥቷቸዋል።
• ከዚህ ሞጁል ጋር እኩል ወይም ዝቅተኛ ትርፍ ያላቸው ተመሳሳይ አይነት አንቴናዎች ብቻ ጥቅም ላይ ሊውሉ ይችላሉ.
• ሌሎች አይነት አንቴናዎች እና/ወይም ከፍተኛ ትርፍ አንቴናዎች ለስራ ተጨማሪ ፍቃድ ሊፈልጉ ይችላሉ።

የምርት መለያ ተገዢነት መረጃን ጨርስ
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:“Contains FCC ID:2AATP-TP300”. The FCC ID can be used only when all FCC compliance requirements are met.

ስለ የሙከራ ሁነታዎች እና ተጨማሪ የሙከራ መስፈርቶች መረጃ
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirements, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

ተጨማሪ ሙከራ፣ ክፍል 15 ንዑስ ክፍል B ማስተባበያ
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rules requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

ለዋና ተጠቃሚ በእጅ መረጃ
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation, and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules

ለውጦችን እንዴት ማድረግ እንደሚቻል - ጠቃሚ ማስታወሻ
እነዚህ ሁኔታዎች ሊሟሉ የማይችሉ ከሆነ (ለምሳሌample፣ የተወሰኑ የላፕቶፕ ውቅሮች ወይም ከሌላ አስተላላፊ ጋር ያለው የጋራ ቦታ)፣ ከዚያ የFCC ፈቃድ ልክ እንደሆነ አይቆጠርም እና የFCC መታወቂያ በመጨረሻው ምርት ላይ መጠቀም አይቻልም። በነዚህ ሁኔታዎች የኦሪጂናል ዕቃ አምራች ኢንተግራተር የመጨረሻውን ምርት (ማስተላለፊያውን ጨምሮ) እንደገና ለመገምገም እና የተለየ የFCC ፍቃድ የማግኘት ሃላፊነት አለበት።

የFCC መግለጫ

ይህ መሳሪያ በሚከተሉት ሁኔታዎች ውስጥ ለ OEM integrators ብቻ የታሰበ ነው።

1. The antenna must be installed such that 20 cm is maintained between the antenna and the user.
2. የማስተላለፊያ ሞጁሉ ከማንኛውም ሌላ አስተላላፊ ወይም አንቴና ጋር ላይገኝ ይችላል።

• Module Antenna Type: 2.4GHz onboard FPC Antenna, 2.68 dBi peak gain.

ይህ መሳሪያ የFCC ደንቦች ክፍል 15ን ያከብራል። ክዋኔው በሚከተሉት ሁለት ሁኔታዎች ተገዢ ነው.

1. ይህ መሳሪያ ጎጂ ጣልቃገብነትን ላያመጣ ይችላል።
2. ይህ መሳሪያ ያልተፈለገ ስራን የሚያስከትል ጣልቃገብነትን ጨምሮ የደረሰውን ማንኛውንም ጣልቃ ገብነት መቀበል አለበት።

ማሳሰቢያ -ለገዢው ተገዢ በሆነው አካል በግልፅ ባልፀደቁት ማናቸውም ለውጦች ወይም ለውጦች ተጠያቂው አይደለም። እንደነዚህ ያሉ ማሻሻያዎች መሣሪያውን የማንቀሳቀስ የተጠቃሚውን ሥልጣን ሊያሳጡ ይችላሉ።

ማሳሰቢያ፡- ይህ መሳሪያ በFCC ህጎች ክፍል 15 መሰረት ተፈትኖ ለክፍል B ዲጂታል መሳሪያ ወሰኖቹን የሚያከብር ሆኖ ተገኝቷል። እነዚህ ወሰኖች የተነደፉት በመኖሪያ ተከላ ውስጥ ካለው ጎጂ ጣልቃገብነት ምክንያታዊ ጥበቃን ለመስጠት ነው። ይህ መሳሪያ አጠቃቀሞችን ያመነጫል እና የሬድዮ ፍሪኩዌንሲ ሃይልን ያሰራጫል እና ካልተጫነ እና በመመሪያው መሰረት ጥቅም ላይ ካልዋለ በሬዲዮ ግንኙነቶች ላይ ጎጂ ጣልቃገብነት ሊያስከትል ይችላል. ነገር ግን, በአንድ የተወሰነ መጫኛ ውስጥ ጣልቃ ገብነት እንደማይፈጠር ምንም ዋስትና የለም. ይህ መሳሪያ በሬዲዮ ወይም በቴሌቭዥን መቀበያ ላይ ጎጂ የሆነ ጣልቃገብነት የሚያስከትል ከሆነ መሳሪያውን በማጥፋት እና በማብራት ሊታወቅ የሚችል ከሆነ ተጠቃሚው ከሚከተሉት እርምጃዎች በአንዱ ወይም ከዚያ በላይ በሆነ መልኩ ጣልቃ ገብነትን ለማስተካከል እንዲሞክር ይበረታታል።

• የመቀበያ አንቴናውን አቅጣጫ ቀይር ወይም ወደ ሌላ ቦታ ቀይር።
• በመሳሪያው እና በተቀባዩ መካከል ያለውን ልዩነት ይጨምሩ.
• መሳሪያውን ተቀባዩ ከተገናኘበት በተለየ ወረዳ ላይ ወደ መውጫው ያገናኙ.
• ለእርዳታ ሻጩን ወይም ልምድ ያለው የሬዲዮ/ቲቪ ቴክኒሻን አማክር።

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule, such as FCC Part 15 Subpart B, before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

የ RF ተጋላጭነት መግለጫ
ይህ መሳሪያ ቁጥጥር ለሌለው አካባቢ የተቀመጡትን የ FCC የጨረር መጋለጥ ገደቦችን ያከብራል። ይህ መሳሪያ በራዲያተሩ እና በሰውነትዎ መካከል ቢያንስ 20 ሴ.ሜ ርቀት ላይ መጫን እና መስራት አለበት።