መመሪያን ተጠቀም
ተርሚናል አድራሻ ፕሮግራመር
| PRG.PAS.MCS |
| 170 x 112 x 35 ሚሜ/270 ግ |
| Plastic case + mechanical keyboard 0°C … 45°C – IP 31 |
| የኃይል አቅርቦት: 9V (ባትሪ/ተሞይ ባትሪ) |
| በ UTP Patch Cable በኩል ወደ ተርሚናል ማገናኘት 0.25 ሴ.ሜ |
| ለፕሮግራም ዝግጁ የሆኑ አድራሻዎች፡ በ"000" እና "998" መካከል "999" መተየብ የአድራሻ ፕሮግራሙን ያበቃል. |
መግለጫ
የ PRG.PAS.MCS programmer allows the programming of the address (apartment number) for all types of terminals in the ክላሲክ መስመር range: PAS.17A, PAS.27X, PAS.37X, MCS.47X.
This programmer serves as the mobile alternative to the terminal address programming function, enabling the address to be programmed both on-site and in the office, by a single person.
ከተርሚናል ጋር ግንኙነት
- የ UTP ጠጋኝ ገመድ 0.25 ሴ.ሜ
- ተመለስ
- ፊት ለፊት
- PRG.PAS.MCS ፕሮግራመር
- ተርሚናል ቪዲዮ – ኦዲዮ (MCS.47X፣ PAS.27X፣ PAS.37X)
አብራ/አጥፋ
- The programmer is turned on by pressing the ON key.
- The programmer turns off:
– 3 seconds after entering the last digit of the programmed address;
– 10 seconds after being turned on, if no key is pressed.
ፕሮግራም ማድረግ
ደረጃ 1፡ Connect the programmer to the terminal.
ደረጃ 2፡ የሚለውን ይጫኑ ON key on the programmer → The display shows [Adresa post]።
ደረጃ 3፡ On the terminal, press and hold the 
ቁልፍ
ደረጃ 4፡ On the programmer, enter the terminal address to be programmed (3 digits required). After entering the last digit, the terminal will issue a confirmation beep, and the key can be released.
07.2025 INS.PRG.PAS.MCS
በአውሮፓ ህብረት የተሰራ በ፡
ELECTRA srl
Parc የኢንዱስትሪ ሚሮስላቫ
ሴንት. ርዕሰ መምህር 33, 707307, Jud. ኢያሺ - RO
+40 232 214.370
sales@electra.ro
www.electra.ro
ድጋፍ
ELECTRA ህንፃ ኮሙኒኬሽን GmbH
ጋድነርጋሴ 71፣ ስቶክወርቅ 1፣ ቡሮ ከፍተኛ 132
1110 Wien – AT
+43 1 810 20 99
sales@electra-automation.at
www.electra-automation.at
ሰነዶች / መርጃዎች
 |
Electra PAS.17A ተርሚናል አድራሻ ፕሮግራመር [pdf] መመሪያ መመሪያ PAS.17A፣ PAS.27X፣ PAS.37X፣ MCS.47X፣ PAS.17A ተርሚናል አድራሻ ፕሮግራመር፣ PAS.17A፣ ተርሚናል አድራሻ ፕሮግራመር፣ አድራሻ ፕሮግራመር፣ ፕሮግራመር |