Pull the lever sideways away from the socket and raise it up to
የ 90 ዲግሪ ማዕዘን.
Locate Pin 1 in the socket and match it with the white dot or
cut edge in the CPU. Insert the CPU smoothly.
Press the lever down to complete the installation.

CPU Core Speed Derivation

The DIP Switch SW1 is used to set the Core/Bus ratio of the CPU.
The actual core speed is calculated by multiplying the Host Clock
Frequency by the Core/Bus ratio.

CPU Speed Setting

To adjust the CPU speed, refer to the CPU specification provided
by the vendor and set SW1 accordingly.

Overclocking Jumper

SW2/SW3 is used for overclocking. Ensure to modify the CPU Bus
ratio through CMOS if using this jumper for overclocking.

CPU Type Selector

Use SW4 to select the CPU type between Intel Coppermine,
Celeron, VIA, or Cyrix Joshua.

Fan Power Connectors

The CPUFAN/PSFAN/SYSFAN connectors support system cooling fans
with +12V. Connect the red wire (positive) to +12V and the black
wire (Ground) to GND. Use specially designed fans with speed
sensors for System Hardware Monitor chipset functionality.

የሚጠየቁ ጥያቄዎች

Q: What should I do if my CPU does not fit into the socket
easily during installation?

A: Ensure that Pin 1 on the CPU aligns correctly with the white
dot or cut edge in the socket before insertion. Do not apply
excessive force when inserting the CPU.

Q: Can I overclock my CPU using this product?

A: Yes, you can overclock your CPU using SW2/SW3 jumpers.
Remember to adjust the CPU Bus ratio through CMOS as well.

View Fullscreen

ምዕራፍ 2

የሃርድዌር ጭነት

ምዕራፍ 2
የሃርድዌር ጭነት
2.1 Central Processing Unit: CPU
The mainboard operates with Intel® CeleronTM processor. The mainboard uses Socket 370 for easy CPU installation and a jumper switch (SW1) to set the proper speed for the CPU. The CPU should always have a Heat Sink and a cooling fan attached to prevent overheating.

2.1-1 CPU Installation Procedure

1. Pull the lever sideways away from the socket. Then, raise the lever up to a 90-degree angle.

ተንሸራታች ሳህን

Open Lever Pin 1

2. Locate Pin 1 in the socket and look for the white dot or cut edge in the CPU. Match Pin 1 with the white dot/cut edge. Then, insert the CPU. It should insert easily.

ሲፒዩ

White dot/ Cut edge
1 ሰካ

3. Press the lever down to complete the installation.

ሊቨርን ዝጋ
ሲፒዩ

2-1

ምዕራፍ 2

የሃርድዌር ጭነት

2.1-1 CPU Core Speed Derivation Procedure

1. The DIP Switch SW1 (1, 2, 3, and 4) is used to set the Core/Bus (Fraction) ratio of the CPU. The actual core speed of the CPU is the Host Clock Frequency multiplied by the Core/Bus ratio. For exampላይ:

ሲፒዩ ሰዓት

Core/Bus ratio

then CPU core speed

= 66MHz = 5.5 = Host Clock x Core/Bus ratio = 66MHz x 5.5 = 333 MHz

SW1

ሲፒዩ

Core/Bus Ratio

ጠፍቷል

2.5

ጠፍቷል

3.5

ጠፍቷል

4.5

ጠፍቷል

5.5

ጠፍቷል

6.5

ጠፍቷል

7.5

ጠፍቷል

ON – Short OFF – Open

2-2

ምዕራፍ 2

የሃርድዌር ጭነት

2.1-2 CPU Speed Setting: SW1
To adjust the speed of the CPU, you must know the specification of your CPU (always ask the vendor for CPU specification).

4 321 እ.ኤ.አ
SW1

2-3

ምዕራፍ 2

የሃርድዌር ጭነት

a. 100MHz CPU Bus Frequency

የሲፒዩ አይነት

SW1

350 ሜኸ

4 321 እ.ኤ.አ

400 ሜኸ

4 321 እ.ኤ.አ

450 ሜኸ

4 321 እ.ኤ.አ

500 ሜኸ

4 321 እ.ኤ.አ

550 ሜኸ

4 321 እ.ኤ.አ

600 ሜኸ

4 321 እ.ኤ.አ

650 ሜኸ

4 321 እ.ኤ.አ

700 ሜኸ

4 321 እ.ኤ.አ

750 ሜኸ

4 321 እ.ኤ.አ

800 ሜኸ

4 321 እ.ኤ.አ

Table 2.1 350 ~ 800MHz Intel®/CeleronTM processor

2-4

ምዕራፍ 2

የሃርድዌር ጭነት

2.1-3 Overclocking Jumper: SW2/SW3
Overclocking is a process of operating a CPU/Processor beyond its specified frequency. SW2/SW3 is used for overclocking.

1 3 እ.ኤ.አ
SW3

1 3 እ.ኤ.አ
SW2

SW2
1 2 3

SW3
1 2 3

ባህሪ
Automatically detect 66MHz, 100MHz CPU Bus Frequency

Virtually set CPU Bus Frequency

into 133MHz

Virtually set CPU Bus Frequency

into 100MHz

Virtually set CPU Bus Frequency

into 66.8MHz

Note: If you used this jumper for overclocking, you also need to modify the CPU Bus ratio thorugh CMOS.

2-5

ምዕራፍ 2

የሃርድዌር ጭነት

2.1-4 CPU Type Selector: SW4

1 3 እ.ኤ.አ
SW4

1
2 3 እ.ኤ.አ
For Intel Coppermine or Celeron

1 2 እ.ኤ.አ
3
For VIA or Cyrix Joshua

2-6

ምዕራፍ 2

የሃርድዌር ጭነት

2.1-5 Fan Power Connectors: CPUFAN/PSFAN/SYSFAN

These connectors support system cooling fan with +12V. It supports three pin head connector. When connecting the wire to the connector, always take note that the red wire is the positive and should be connected to the +12V, the black wire is Ground and should be connected to GND. If your mainboard has System Hardware Monitor chipset on-board, you must use a specially designed fan with speed sensor to take advantage of this function.

ሲፒዩፋን

ዳሳሽ

ጂኤንዲ

+ 12 ቪ

SENSOR +12V GND
PSFAN (Optional)

SENSOR +12V GND
SYSFAN (Optional)
PSFAN : Power Supply Fan (Optional) CPUFAN : Processor Fan SYSFAN : System(Chassis) Fan (Optional)
For fans with fan speed sensor, every rotation of the fan will send out 2 pulses. System Hardware Monitor will count and report the fan rotation speed.
Note: 1. Always consult vendor for proper CPU cooling fan. 2. PSFAN & SYSFAN are for System Hardware Monitor only.
2-7

ምዕራፍ 2

የሃርድዌር ጭነት

2.2 Clear CMOS Jumper: JBAT1
A battery must be used to retain the mainboard configuration in CMOS RAM. Short 1-2 pins of JBAT1 to store the CMOS data.

1
3
ጀባቲ1

1 2 3
ውሂብ አቆይ

1 2 3
ውሂብ አጽዳ

ማስታወሻ፡-

You can clear CMOS by shorting 2-3 pin, while the system is off. Then, return to 1-2 pin position. Avoid clearing the CMOS while the system is on, it will damage the mainboard. Always unplug the power cord from the wall socket.

2-8

ምዕራፍ 2

የሃርድዌር ጭነት

2.3 ማህደረ ትውስታ መጫን
2.3-1 Memory Bank Configuration
The mainboard supports a maximum memory size of 256MB (8M x 8) or 512MB (16M x 4) registered DIMM for SDRAM: It provides two 168-pin unbuffered DIMMs (Double In-Line Memory Module) sockets. It supports 8 MB to 256 Mbytes DIMM memory module.

DIMM2(Bank2+ Bank3) DIMM1(Bank0 + Bank1)

!
ማስጠንቀቂያ!

There are two kinds of DIMM specification supported
by this mainboard: PC133, PC100 and PC66. If you use 66MHz CPU Bus Frequency, these two DIMM Specs. is supported. If you use 100 MHz CPU Bus Frequency, only PC100 DIMM Specs. is supported. If you use 133MHz CPU Bus Frequency, only PC133 DIMM specs will be supported.

2-9

ምዕራፍ 2

የሃርድዌር ጭነት

2.3-2 Memory Installation Procedures A. How to install a DIMM Module

Single Sided DIMM

Double Sided DIMM
1. The DIMM slot has a two Notch Key “VOLT and DRAM”, so the DIMM memory module can only fit in one direction.
2. Insert the DIMM memory module vertically into the DIMM slot. Then push it in.

ድራም

ቮልት

3. The plastic clip at the side of the DIMM slot will automatically close.

2-10

ምዕራፍ 2

የሃርድዌር ጭነት

2.3-3 Memory Population Rules 1. Supports only SDRAM DIMM.
2. To operate properly, at least one 168-pin DIMM module must be installed.
3. This mainboard supports Table Free memory, so memory can be installed on DIMM1 or DIMM 2 in any order.
4. Supports 3.3 volt DIMM.
5. The DRAM addressing and the size supported by the mainboard is shown below:

Table 2.3-1 SDRAM Memory Addressing

DRAM Tech. 16M 64M
64 ሚ

DRAM Density &
Width 1Mx16
2Mx8 4Mx4 2Mx32 2Mx32 4Mx16 4Mx16 8Mx8 16Mx4 2Mx32 4Mx16 8Mx8 16Mx4

DRAM Addressing
ASYM ASYM ASYM ASYM ASYM ASYM ASYM ASYM ASYM ASYM ASYM ASYM ASYM

Address Size

MB/DIMM

ረድፍ

አምድ

Single no. Side(S) pcs.

Double no. Side(D) pcs.

8MBx4 16MBx8

9 16MBx8 32MBx16

32 ሜባ 64 ሜባ

9 32MBx2 64MBx4

8 16MBx2 32MBx4

32 ሜባ 64 ሜባ

64 ሜባ 128 ሜባ

10 128MB 256MB

16 ሜባ 32 ሜባ

32 ሜባ 64 ሜባ

64 ሜባ 128 ሜባ

10 128MB 256MB

2-11

ምዕራፍ 2

የሃርድዌር ጭነት

2.4 Case Connector: JFP1
The Power Switch, Reset Switch, Power LED, Speaker, Keylock and HDD LED are all connected to the JFP1 connector block.

መቀየሪያን ዳግም አስጀምር

ተናጋሪ

Buzzer (short pin)

ኃይል

ቀይር

ድርብ

ነጠላ

ቀለም
LED

ኃይል LED +

ኤችዲዲ

LED

የቁልፍ ቁልፍ
JFP1 እ.ኤ.አ.

2-12

ምዕራፍ 2

የሃርድዌር ጭነት

2.4-1 Power Switch Connect to a 2-pin push button switch. This switch has the same feature with JRMS1.
2.4-2 Reset Switch Reset switch is used to reboot the system rather than turning the power ON/ OFF. Avoid rebooting while the HDD LED is lit. You can connect the Reset switch from the system case to this pin.
2.4-3 Power LED The Power LED is lit while the system power is on. Connect the Power LED from the system case to this pin. There are two types of LED that you can use: 3-pin single color LED or 2-pin dual color LED(ACPI request).
a. 3 pin single color LED connect to pin 4, 5, & 6. This LED will lit when the system is on.
b. 2 pin dual color LED connect to pin 5 & 6. GREENColor: Indicate the system is in full on mode. ORANGE Color: Indicate the system is in suspend mode.
2.4-4 Speaker Speaker from the system case is connected to this pin. If on-board Buzzer is available: Short pin 14-15: On-board Buzzer Enabled. Open pin 14-15: On-board Buzzer Disabled.
2.4-5 HDD LED HDD LED shows the activity of a hard disk drive. Avoid turning the power off while the HDD led is lit. You can connect the HDD LED from the system case to this pin.
2.4-6 Keylock Keylock allows you to disable the keyboard for security purposes. You can connect the keylock to this pin.

2-13

ምዕራፍ 2

የሃርድዌር ጭነት

2.5 Floppy Disk Connector: FDD
The mainboard also provides a standard floppy disk connector FDD that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables.
FDD

2-14

ምዕራፍ 2

የሃርድዌር ጭነት

2.6 Hard Disk Connectors: IDE1 & IDE2
The mainboard has a 32-bit Enhanced PCI IDE Controller that provides PIO mode 0~4, Bus Master, and Ultra DMA/66 function. It has two HDD connectors IDE1 (primary) and IDE2 (secondary). You can connect up to four hard disk drives, CD-ROM, 120MB Floppy (reserved for future BIOS) and other devices to IDE1 and IDE2. These connectors support the provided IDE hard disk cable.

Secondary IDE Connector Primary IDE Connector

IDE1(Primary IDE Connector) The first hard drive should always be connected to IDE1. IDE1 can connect a Master and a Slave drive. You must configure second hard drive to Slave mode by setting the jumper accordingly. IDE2(Secondary IDE Connector) IDE2 can also connect a Master and a Slave drive.
2-15

ምዕራፍ 2

የሃርድዌር ጭነት

2.7 የኃይል አቅርቦት

2.7-1 ATX 20-pin Power Connector: JWR1

This connector supports the power button on-board. Using the ATX power supply, functions such as Modem Ring Wake-Up and Soft Power Off are supported by this mainboard. This power connector supports instant power on function which means that system will boot up instantly when the power connector is inserted on the board.

ATX

የኃይል ማገናኛ

የፒን ትርጉም

ፒን

ሲግናል

3.3 ቪ

ጂኤንዲ

PW_እሺ

5V_SB

12 ቪ

ፒን

ሲግናል

3.3 ቪ

-12 ቪ

ጂኤንዲ

PS_ON

ጂኤንዲ

-5 ቪ

Warning: Since the mainboard has the instant power on function, make sure that all components are installed properly before inserting the power connector to ensure that no damage will be done.

2-16

ምዕራፍ 2

የሃርድዌር ጭነት

2.7-2 Remote Power On/Off Switch: JRMS1
Connect to a 2-pin push button switch. During OFF state, press once and the system turns on. During ON stage, push once and the system goes to sleep mode: pushing it more than 4 seconds will change its status from ON to OFF. If you want to change the setup, you could go to the BIOS Power Management Setup. This is only used for ATX type power supply.

JRMS1

2-17

ምዕራፍ 2

የሃርድዌር ጭነት

2.8 IrDA Infrared Module Connector: IR
The mainboard provides one 5-pin infrared (IR) connector for IR modules. This connector is for optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. FIR and Consumer IR are reserved functions.

IRTX

GND IRRX

ቪሲሲ

2-18

ምዕራፍ 2

የሃርድዌር ጭነት

2.9 Serial Port Connectors: COM A and COM B
The mainboard has two 9-pin male DIN connector for serial ports COM A & COM B. These ports are 16550A high speed communication port that send/ receive 16 bytes FIFOs. You can attach a mouse or a modem cable directly into this connector.

1 234 5

678 9 እ.ኤ.አ
COM ኤ

COM ቢ

Serial Port (9-pin Male)

የፒን ትርጉም

ፒን
1 2 3 4 5 6 7 8 9

ሲግናል
DCD(Data Carry Detect) SIN(Serial In or Receive Data) SOUT(Serial Out or Transmit Data) DTR(Data Terminal Ready) GND DSR(Data Set Ready) RTS(Request To Send) CTS(Clear To Send) RI(Ring Indicate)

2-19

ምዕራፍ 2

የሃርድዌር ጭነት

2.10 Parallel Port Connector: LPT

The mainboard provides a 25 pin female centronic connector for LPT. A parallel port is a standard printer port that also supports Enhanced Parallel Port(EPP) and Extended capabilities Parallel Port(ECP). See connector and pin definition below:

Parallel Port (25-pin Female)

LPT

የፒን ትርጉም

ፒን

ሲግናል

STROBE

መረጃ

ACK#

ስራ የሚበዛበት

ምረጥ

ፒን

ሲግናል

AUTO FEED#

ስህተት#

INIT#

SLIN#

ጂኤንዲ

2-20

ምዕራፍ 2

የሃርድዌር ጭነት

2.11 Mouse Connector: JKBMS1

The mainboard provides a standard PS/2® mouse mini DIN connector for attaching a PS/2® mouse. You can plug a PS/2® mouse directly into this connector. The connector location and pin definition are shown below:

ፒን6 ኤንሲ
Pin4 VCC
ፒን2 ኤንሲ

Pin5 Mouse Clock
ፒን3 ጂኤንዲ
Pin1 Mouse DATA

PS/2 Mouse (6-pin Female)

2.12 Keyboard Connector: JKBMS1
The mainboard provides a standard PS/2® keyboard mini DIN connector for attaching a keyboard. You can plug a keyboard cable directly to this connector.

ፒን6 ኤንሲ
Pin4 VCC
ፒን2 ኤንሲ

Pin5 KBD Clock
Pin3 Pin1 GND KBD DATA

PS/2 Keyboard (6-pin Female)

2-21

ምዕራፍ 2

የሃርድዌር ጭነት

2.13 Joystick/Midi Connectors
You can connect joystick or game pads to this connector. Joystick/MIDI

2.14 Audio Port Connectors
Line Out is a connector for Speakers or Headphones. Line In is used for external CD player, Tape layer, or other audio devices. Mic is a connector for the microphones.
Line Out Line In Mic
1/8″ Stereo Audio Connectors

2-22

ምዕራፍ 2

የሃርድዌር ጭነት

2.15 የዩኤስቢ ማገናኛዎች
The mainboard provides a UHCI(Universal Host Controller Interface) Universal Serial Bus root for attaching USB devices like: keyboard, mouse and other USB devices. You can plug the USB device directly to this connector.
የዩኤስቢ ወደብ 2

1 2 3 4
የዩኤስቢ ወደብ 1

የፒን ሲግናል

ቪሲሲ

- ውሂብ 0

ጂኤንዲ

+ ውሂብ0

2-23

ምዕራፍ 2

የሃርድዌር ጭነት

2.16 Power Saving Switch Connector: JGS1
Attach a power saving switch to JGS1. When the switch is pressed, the system immediately goes into suspend mode. Press any key and the system wakes up.

JGS1

2-24

ምዕራፍ 2

የሃርድዌር ጭነት

2.17 Power Saving LED Connector: JGL1
JGL1 can be connected with two-color LED. There are two type of LED that you can use: 3-pin LED or 2-pin LED(ACPI request). LED will lit while the system is in suspend mode.

3-pin LED

አረንጓዴ ቀለም

ብርቱካንማ ቀለም

1-2 Single Color 1-3 Blink

+1 3
JGL1

2-pin LED

አረንጓዴ ቀለም
ብርቱካንማ ቀለም

1-2 Dual Color

2-25

ምዕራፍ 2

የሃርድዌር ጭነት

2.18 Wake-Up on LAN Connector: JWOL1
The JWOL1 connector is for use with LAN add-on cards that supports Wake Up on LAN function. To use this function, you need to set the “Wake-Up on LAN” to enable at the BIOS Power Management Setup.

1 3 እ.ኤ.አ
JWOL1

ፒን

ሲግናል

5VSB

ጂኤንዲ

MP_WAKEUP

Note: LAN wake-up signal is active “high”.

ማስታወሻ፡-

To be able to use this function, you need a power supply that provide enough power for this feature. (Power supply with 750 mA 5V Stand-by)

2-26

ምዕራፍ 2

የሃርድዌር ጭነት

2.19 Modem Wake Up Connector: JMDM1
The JMDM1 connector is for used with Modem add-on card that supports the Modem Wake Up function. To use this function, you need to set the “Resume By Ring” to enable at the BIOS Power Management Setup.

ጄኤምዲኤም1

ፒን

ሲግናል

ጂኤንዲ

MDM_WAKEUP

5VSB

Note: Modem wake-up signal is active “low”.

ማስታወሻ፡-

To be able to use this function, you need a power supply that provide enough power for this feature. (Power supply with 750 mA 5V Stand-by)

2-27

ምዕራፍ 2

የሃርድዌር ጭነት

2.20 Modem-In: J6
The connector is for Modem with internal voice connector.

SPK IN GND
MIC ወጣ
J6
SPK_IN is connected to the Modem Speaker Out connector. MIC_OUT is connected to the Modem Microphone In connector.

2-28

ምዕራፍ 2

የሃርድዌር ጭነት

2.21 AUX Line In Connector: J5
This connector is used for DVD Add on Card with Line In connector.

L GND R
J5

2-29

ምዕራፍ 2

የሃርድዌር ጭነት

2.22 CD-In Modem Connector: J8
This connector is for Modem with internal voice connector.

LGND R
J8

2-30

ምዕራፍ 2

የሃርድዌር ጭነት

2.23 Keyboard Power: JVSB1
The JVSB1 jumper is for setting keyboard power. This function is provided for keyboard and PS/2 mouse Wake-up function.

1 3 እ.ኤ.አ
JVSB1

1
3
5V Standby (default) Enable keyboard power on function

1
3
5V Disable keyboard power on function

Note: To be able to use this function, you need a power supply that provide enough power for this feature. (Power supply with 750 mA 5V Stand-by)
2-31

ምዕራፍ 2

የሃርድዌር ጭነት

2.24 Chassis Intrusion Switch Case: JCASE1
This connector is connected to 2-pin connector chassis switch. If the Chassis is open, the switch will be short. The system will record this status. To clear the warning, you must enter the BIOS setting and clear the status.

JCASE1

2-32

ምዕራፍ 2

የሃርድዌር ጭነት

2.25 USB Front Connector: USB2
The mainboard provides a Front Universal Serial Bus Connector.

ዩኤስቢ2

ፒን

መግለጫ

1፣ 10

ቪሲሲ

2፣ 9

- ውሂብ

3፣ 8

+ ውሂብ

4, 5, 6, 7 GND

2-33

ምዕራፍ 2

የሃርድዌር ጭነት

2.26 USB Front Connector & Rear Port Jumpers: J14 & J15
This jumper is used to Enabled or Disabled the USB Front Connector. If the USB Front connector is set to enabled, the top USB port at the rear I/O panel will be disabled. If the USB Front connector is set to disabled, the USB ports at rear I/O panel will both be operational.

ጄ14

ጄ15

USB Rear Port

ጄ14
Short 2-3 5-6

ጄ15
Short 2-3 5-6

Front Short 1-2 Short 1-2

ማገናኛ

4-5

2-34

ምዕራፍ 2

የሃርድዌር ጭነት

2.30 Front Panel Audio Connector: J13
The mainboard provides a Front Panel Audio connector. This is an optional Audio connector for Front Panel.

ጄ13

Pin 1, 4, 7 3, 8 5 6 10 9

Signal Audio GND System GND Line Out (L) Line Out (R) MIC In +12V

2-35

ሰነዶች / መርጃዎች

Intel Celeron ፕሮሰሰር [pdf] የመጫኛ መመሪያ
ms-6154va, Celeron Processor, Processor

ዋቢዎች

የተጠቃሚ መመሪያ

Intel Celeron Processor Installation Guide

Celeron Processor

የምርት መረጃ

ዝርዝሮች

የምርት አጠቃቀም መመሪያዎች

Installation of CPU

CPU Core Speed Derivation

CPU Speed Setting

Overclocking Jumper

CPU Type Selector

Fan Power Connectors

የሚጠየቁ ጥያቄዎች

Q: What should I do if my CPU does not fit into the socket
easily during installation?

Q: Can I overclock my CPU using this product?

ሰነዶች / መርጃዎች

ዋቢዎች

አስተያየት ይስጡ

ምላሽ ሰርዝ