sensor switch WSRA Series Wall Switch Sensor with Occupancy

ዝርዝር መግለጫዎች፡-

• Series: WSRA Series
• Operational Settings: Occupancy Time Delay, On Mode, Switch
• Modes, Darkness Set-Point, Photocell Mode, LED Operation, Manual On
• Grace Period, Predictive Exit Time, Predictive Grace Time, Fade On Rate

Occupancy Time Delay:
The occupancy sensor can be set to keep the lights on for different durations after detecting occupancy. Adjust the setting as per your preference.

ሞድ ላይ፡

Choose between Automatic On, Manual On, or Reduced Turn-On modes based on your requirements. Automatic On turns the lights on automatically upon occupancy detection, Manual On requires manual intervention to turn the lights on, and Reduced Turn-On initially ignores small motions.

የመቀየሪያ ሁነታዎች፡-
Switch between different modes such as Switch Disable, Predictive Mode, and Predictive Mode with Expiration. These modes control how the sensor operates after a certain period of inactivity.

Darkness Set-Point / Inhibit Set-Point:
Set the ambient light level at which the lights will be adjusted to the High Trim setting. The Set Now option automatically selects the Darkness Set-Point based on current conditions in the room.

Photocell ሁነታ
Enable or disable the feature that prevents lights from turning on when the light level is above the Inhibit Set-Point.

ነባሪዎችን ወደነበሩበት መልስ
Reset all functions to their original settings if needed.

የ LED ኦፕሬሽን
Select the behavior of the device’s LED indicator.

Manual On Grace Period
Set a grace period for manual control of the lights when in Manual On mode.

Predictive Exit Time and Predictive Grace Time
Adjust the time intervals for predictive exit and grace periods when occupants leave the room.

Fade On Rate
Set the time required for the lights to reach their preset brightness level.

Operational  settings

Occupancy Time Delay:
የነዋሪነት ዳሳሽ መብራቱን ለመጨረሻ ጊዜ ካወቀ በኋላ የሚቆይበት ጊዜ።

3=On Mode
ከቫካንሲ (VA) አማራጭ ጋር ተፈጻሚ አይሆንም

ራስ-ሰር በርቷል
አነፍናፊ መብራቱን ሲያውቅ በራስ-ሰር ያበራል።

መመሪያ በርቷል
ዳሳሽ መብራቱን ለማብራት ቁልፉን መጫን ያስፈልገዋል።

የተቀነሰ ማብራት
ዳሳሽ መጀመሪያ ላይ ትላልቅ እንቅስቃሴዎችን ብቻ እንዲያገኝ ተዋቅሯል፣ ማንኛውም የተንጸባረቀ የፓሲቭ ኢንፍራሬድ (PIR) ምልክቶችን በብቃት ችላ በማለት። የ PIR ምልክታቸው ትልቅ ስለሆነ ተሳፋሪዎች ወደ ክፍሉ ሲገቡ ወዲያውኑ ይታያሉ። መብራቶች አንዴ ከበሩ፣ ዳሳሹ ወደ ከፍተኛ ትብነት ይመለሳል።

1. ራስ-ሰር በርቷል
2. የተቀነሰ ማብራት
3. Manual On ‘

4=Switch Modes
ከቫካንሲ (VA) አማራጭ ጋር ተፈጻሚ አይሆንም

ቀይር አንቃ (ይሻር)
Button will turn lights And keep them off until pressed again. The lights will remain off until the button IS pressed again, resetting the sensor to Automatic On mode.
ቀይር አሰናክል
ተጠቃሚው መብራቶቹን በፑሽ-አዝራሩ በኩል እንዳያጠፋ ተከልክሏል።
ትንበያ ሁነታ
Pressing the push-button switch turns the lights off and temporarily disables the occupancy detection. After 10 seconds, the occupancy detection reactivates am mmttors for an additional 30 seconds. no «upancyls detected during this period” the sensor will revert to Automatic On operation. If occupancy is detected the sensor will remain in Override Off mode and requires the switch to be pressed in order to restore the sensor to Automatic On.

Predictlve Mode wdth Expiratlon
Pressing push-button switch turns the lights off and temporarily disables the occupancy detection. After 10 s«mds, the occupancy detection reactivates am mmltors for an additional 30 seconds If no occupancy is detected during this period” the gnsor WII/reverts to Automatic On operation.

1. ቀይር አንቃ
2. ቀይር አሰናክል
3. ትንበያ ሁነታ
4. Predictive Mode with Expiration.

5=Darkness Set-Point / Inhibit Set-Point
አነፍናፊው መብራቶቹን ወደ High Trim ቅንብር የሚያዘጋጅበት የድባብ ብርሃን ደረጃ።

በማቀናበር ላይ	Light Level (fc)	ማስታወሻዎች
1	Set NOW*	Default/current setting
2	0.1 fc	Very low light
3	1 fc	ዝቅተኛ ብርሃን
4	4 fc	Moderate low light
5	8 fc	መካከለኛ ብርሃን
6	16 fc	Medium-high light
7	24 fc*	Default recommended
8	32 fc	ብሩህ ብርሃን
9	48 fc	በጣም ብሩህ
10	64 fc	ከፍተኛ ብርሃን
11	ጠፍቷል	Light level off
12	96 fc	Maximum standard brightness
13	128 fc	Extra bright
14	192 fc	እጅግ በጣም ብሩህ
15	256 fc	ከፍተኛ ቅንብር

Set Now will automatically select the Darkness Set-Point based on the current conditions in the room. Lights will go to full bright and sensor will rapidly flash for 15 seconds, allowing the occupant to move out of direct view የዳሳሽ. አንዴ የተቀመጠ-ነጥብ ምርጫ ከተጠናቀቀ በኋላ፣ አነፍናፊው በማረጋገጫ ድርብ ብልጭ ድርግም ይላል።

7=Photocell Mode

መከልከል ብቻ
Prevents lights from automatically coming on when light level is above the Inhibit Set-Point

1. ተሰናክሏል።
2. መከልከል ብቻ

9=Restore Defaults
Returns all functions to their original settings.

1. የአሁኑን አቆይ*
2. ነባሪዎችን ወደነበሩበት መልስ

11=LED Operation
Indicates behavior of the device’s LED.

1. የመኖሪያ ቦታ አመላካች*
2. ተሰናክሏል።

14 = የጸጋ ጊዜ መመሪያ
Time period after lights automatically turn off that tho can be reactivated by motion, Applicable only when sensor is in Manual On (Semi Auto) mmie.

• I-Osec
• 3-15see

17 = የመውጫ ጊዜ
Time period after manually switching fights off to leave the space. Applicob/e onbe when sensor in Predictive Off mode.

• I-5s«
• 2-6 ሴ
• 3-7s«
• 4-8 ሴ
• 5-9 ሴ
• 6-10 ኪ*
• 7-15 ኪ
• 8-20 ሴ
• 9-30 ኪ

18 = ትንበያ ጸጋ ጊዜ
Time period after Predictive Exit Time fiat sensor rescans the RMRN for remaining occupants. Applicable only when sensor is in Predictive Off mode.

• I-Osec
• 2-5s«
• 3-10 ኪ
• 4-20 ሰከንድ
• 5-30see
• 6-40 ኪ
• 7-50 ሰከንድ
• 8-60 ሴ

19 = ተመን ላይ ደብዝዝ
Time required for light to reach preset IceL

• 1-0.75 see
• 2-25 ሴ
• 3-5 ሴ
• 4-15s«

20 = ደብዝዝ ጠፍቷል ተመን
Time required for light to turn Off

• 1-0.75 ሰከንድ
• 2-15see
• 3-5 ሴ
• 4-15 ሴ

የክወና ቅንብር መመሪያዎች

PLEASE READ A1 1 7 STEPS BEFORE PROGRAMMING

• Enter programming mode by pressing & holding button until LED flashes rapidly. Release button.
• Enter a specific function by pressing button. The number Of times as the desired function number from the tables on the following pages (e.g., press twice for function 2, Occupancy Time Delay).
• The selected function’s current setting will then be read out in a sequenæ of LED flashes (e.g., five flashes for 10 min). TO change setting, proceed to step 4 before sequence repeats 10 times.
• While the sensor is flashing back current setting, interrupt it by pressing button the number of times for the new desired setting as indicated in the particular function’s detailed table (e.g., press seven times for 15 min). Sensor will begin to flash new setting as confirmation.
• Next, while the sensor is flashing back new setting, interrupt it by pressing and holding button until LED flashes rapidly. Release button.
• As final confirmation and activation Of the new setting, re-enter the function number that was changed (e.g., press twice for function 2, Occupancy Time Delay).
• LED will flash twice indicating acceptance of new setting. If two flashes are not seen, repeat 7 step process

ማስታወሻ፡-

TO exit programming mode without saving or to change to a different function, wait for the blink back sequence to repeat 10 times, then return to step 1.

ዋስትና
የ 5-አመት ዋስትና. የተሟሉ የዋስትና ውሎች በ ላይ ይገኛሉ www.acuibrands.com/CustomerResourcesTerms_and_conditions.as x

ሁሉንም የደህንነት መመሪያዎች ያንብቡ እና ይከተሉ!

እነዚህን መመሪያዎች ያስቀምጡ እና ከተጫነ በኋላ ለባለቤቱ ያቅርቡ

• Acuity Brands I One Lithonia Way Conyers, GA 30012
• ስልክ፡ 800.535.2465 www.acuitybrands.com/sensorswitch @2014-2021 Acuity Brands Lighting, Inc.
• All rights reserved. Rev. 09/27/21 lofl 912-00262-002

የሚጠየቁ ጥያቄዎች

How do I reset all settings to default?

Navigate to the Restore Defaults option and select 'Restore Defaults' to reset all functions to their original settings.

ሰነዶች / መርጃዎች

sensor switch WSRA Series Wall Switch Sensor with Occupancy [pdf] የመጫኛ መመሪያ is-wsra 220VAC Edits V5, WSRA Series Wall Switch Sensor with Occupancy, WSRA Series, Wall Switch Sensor with Occupancy, Switch Sensor with Occupancy, Sensor with Occupancy

ዋቢዎች

• የተጠቃሚ መመሪያ