T238 Digital Trigger Unit V2&V3 BASIC

(With short-circuit protection)

ማስጠንቀቂያ
This upgrade kit is designed for professional AIRSOFT/gel ball blaster player who can fully disassemble and assemble Automatic Electric Gun. The compatibility with all Gearboxes is not guaranteed, but it can fit into standard or common brand Gearboxes V2/V3 without larger modification. Related Tools and skills is needed for installing the product.

ትኩረት

1. Protect the detection sensors/switches while installing, do not connect the battery for testing before installation is completed to prevent damage to the circuit board.
2. የሞተርን አወንታዊ እና አሉታዊ ነገር አስቡ, አይገለበጡ.
3. DTU will not function properly until the gearbox and motor are installed correctly. Please finish the installation at first.
4. እባክዎን ከM150 ያነሰ ስፕሪንግ ይጠቀሙ።
5. Please keep your gearbox clean, and keep the sensors D5, D6 clean.

መግለጫ

T238 digital trigger unit BASIC is a programmable MOSFET designed for beginners who only need simple functions like stable semi-auto and preventing battery over discharge. With high speed processor and 2 high power MOSFET chips, this system has many functions, such as binary trigger, auto-loading function for gel ball magazine, over heat protection and so on. Besides, it also has the functions of gearbox block-up protection. It can effectively improve the stability, shooting speed and response speed of gearbox. The module uses a maximum of 16.8V batteries. Soldering and wiring are required.

ዋና መለኪያዎች

• Size of V2: 45*30*14mm/V3: 100*23*5mm
• የአሠራር ጥራዝtagሠ: 6-16.8V
• MOSFET overheat protection
• Motor short circuit protection
• ባትሪ ከመጠን በላይ የመፍሰሻ መከላከያ
• Active brake tech
• ማርሽ ለማግኘት የጨረር ዳሳሽ ይጠቀማል
• Binary trigger and paint ball shooting mode
• ከፍተኛው Inrush current 300A ነው፣ ከፍተኛው የብሬክ ጅረት 100A ነው።
• Compatible with various Standard Gearbox V2/V3

ተግባራት

1. Binary trigger. when the trigger is pressed and released, the gearbox will fire once each.
2. የማገጃ መከላከያ. Gearbox Block-up ሲከሰት ስርዓቱ መስራት ያቆማል እና የተራዘመ የ'ቢፕ' ድምጽ ያሰማል። እባክዎን በኃይል በማጥፋት ወዲያውኑ የሞገድ ሳጥኑን ያረጋግጡ።
3. አውቶማቲክ የመጫን ተግባር የተቀየሰው ለጄል ኳስ ፍንዳታ መጽሔቶች በሞተር ውስጥ ነው ፣ መጽሔቱን በሚቀይሩበት ጊዜ የመጽሔቱ ሞተር ለ 1 ሰከንድ በራስ-ሰር ይሠራል።
4. Short circuit protection. When a short circuit is detected in the motor/magazine circuit, the system will cut off the power to the motor/magazine and prompt through LED flashing. Please disconnect the battery in a timely manner and troubleshoot the problem.
5. Battery Over-Discharge Protection: The system automatically detects the number of battery cells. When the voltage of any single cell drops below the preset threshold, the system will: Emit an audible “Beep! Beep! Beep! Beep!” warning through the motor. Enter shutdown/sleep mode. Please immediately replace the battery upon hearing the low-voltagሠ ማንቂያ።
6. When the MOSFET is overheated, after the trigger is pulled, the motor will give a beep prompt until it is automatically restarted after cooling.

ሁነታዎች

Binary-trigger mode: In this mode, when the trigger is pressed and released, the gearbox will fire once each
Paint Ball Mode: In this mode, if the trigger switch is triggered at a slower frequency, the system is in single shot mode. If the trigger switch is triggered at a faster frequency, the system is in Binary-trigger mode

መስፈርቶች

1. Teflon high-temperature resistant wire is recommended for this system, power wire for motor and battery should be larger than 0.5sqm silver plate wire, wire for electronic powered magazine should be around 0.25sqm
2. Using high magnetic motors and high discharge rate batteries to reduce motor and battery heating caused by frequent single shot shooting
3. It is recommended to use springs below M150, and for springs exceeding M150, please use a high torque motor
4. ከፍተኛ የማሽከርከር ሞተር ይጠቀሙ ሞተሩን በፍጥነት ያቆማል እና DTU ከመጠን በላይ እንዳይሞቅ ይከላከላል።
5. In standby state, the current of the system is smaller than 0.01A. Please disconnect the battery if it is not used for a long time

መጫን

1. Please refer to relevant tutorials to remove the gearbox from the receiver
2. የማርሽ ሳጥኑን ይንቀሉ ፣ የተቆረጠውን ዱላ ማውለቅ አስፈላጊ ነው ፣ የሴፍቲ ሊቨር እና መራጭ ሳህን በማርሽ ሳጥኑ ላይ ያስቀምጡ (የዲስፕሌይ ማርሽ ሳጥኑን ዩቲዩብ ላይ ማግኘት ይቻላል)
3. ሞጁሉን ይጫኑ እና ገመዶቹን በማርሽ ሳጥኑ ውስጥ ይግፉ (አንዳንድ የማርሽ ሳጥኑ ጠንከር ያለ ወይም የተቆፈረ ጉድጓድ መቁረጥ ያስፈልጋል)
4. የማርሽ ሳጥኑን ሰብስብ
5. ለተጨማሪ ዝርዝሮች፣ ይጎብኙ http://t238.net

ፈጣን ሙከራ
After soldering, connect the motor and battery. Make sure the wires are connected correctly. Press each switch one by one, you will get a blink of the LED. If not, your module is not right, contact the customer service immediately.
Notice! Ensure that the motor is securely fastened to prevent sudden start-up.
When testing the gear sensors, use an opaque object to cover between D5 and D6 to trigger the gear sensor. If the gear sensor is working properly, the LED will flash once when the opaque object intervenes.

ፕሮግራም ማውጣት

1. Follow the steps below to enter programming mode
2. በፕሮግራም ሁነታ, ሞተሩ አጭር "ቢፕ" ያወጣል, "ቢፕ" ቁጥሮች የአማራጭ ተከታታይ ቁጥር ማለት ነው. አማራጩን ለመምረጥ ከፈለጉ ቀስቅሴውን በ2 ሰከንድ ውስጥ ‘ቢፕ’ እስከ ረጅም ‘ቢፕ’ ካደረጉ በኋላ ያዙት ፣ ሞጁሉ ወደ ተዛመደ አማራጭ ይቀናበራል። (አማራጮች እና የተዛመደ ተግባር/መለኪያ ከዚህ በታች ባለው ሠንጠረዥ ውስጥ ይገኛሉ)።
3. After setting to the selected option, the motor emits short ‘beep’s, the number of ‘beep’s means the different function/parameter of this option. If you want to program to set it to certain option or parameter, pull and hold the trigger in 2 second after ‘beep’ till 2 long ‘beep’, then the module exits the programmable mode.

አማራጭ \ መለኪያ	1	2	3
1 የባትሪ ጥበቃ	ጠፍቷል (ነባሪ)	ON	ዳግም አስጀምር
2 ከፊል ራስ-ሰር ሁነታ	Semi-auto(Default)	ሁለትዮሽ ቀስቅሴ	Paint ball
3 የመራጭ ዓይነት	G36(Default)	AK47

መተኮስ ችግር

1. The green circle represents the contour line of the circuit board, representing the position of the circuit board. The red circle represents the center of the gear shaft, representing the gear position. When installed correctly, the green circle should be coaxial with the red circle.
2. ቀዩ ክብ ከአረንጓዴው ክብ ጋር ያልተማከለ ከሆነ, የ DTU እና የማርሽ ሳጥን መጠን እንደማይዛመዱ ያሳያል, እና የሴክተሩ ማርሽ መቀየር ያስፈልገዋል.
3.  When the green circle is to the left of the red circle, the red position of sector gear needs to be removed by 1mm; When the green circle is to the right of the red circle, the green position of sector gear needs to be extended by 1mm.

ቢኢፒ

• Beep!: represents a short beep.
• Beep~: represents a long beep.

Beep types	ትርጉም
Beep!Beep!Beep!	Successfully initialized prompt tone, system enters game mode
Beep!Beep!Beep!Beep!	ባትሪ ዝቅተኛ መጠንtage or exceeding allowable voltage
Beep~	Gear sensor cannot detect gear rotation; Damaged gear sensor or abnormal connection with DTU; Gearbox jamming or motor polarity reversal; Programming mode prompt sound
Beep~Beep~	Enter and exit program mode
ቢፕ!	Overheat warning/switching fire mode/Switch shooting mode with selector

የ LED ዓይነት	ትርጉም
ሁልጊዜ በርቷል	The motor is not connected to the DTU; Motor damage; Damaged motor wire plug
Always fast flashing	Short circuit between the positive and negative poles of the motor; LED fast flashing indicates a short circuit in the gearbox motor circuit; Internal motor malfunction; Low battery
Always slow flashing	Short circuit between the positive and negative poles of the magazine, LED slow flashing indicates a short circuit in the magazine circuit; Internal motor malfunction; Low battery
አንዴ ብልጭታ	Switch/sensor triggered

ሰነዶች / መርጃዎች

T238 T238 Digital Trigger Unit Light Sensor [pdf] መመሪያ መመሪያ T238 Digital Trigger Unit Light Sensor, T238, Digital Trigger Unit Light Sensor, Trigger Unit Light Sensor, Unit Light Sensor, Light Sensor

ዋቢዎች

• የተጠቃሚ መመሪያ